Bedienungsanleitung Alpine CDE-135BT (Seite 10 von 46) (Englisch)

536969

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

10-EN

Press RESET with a ballpoint pen or similar pointed object.

Adjusting Volume

Turn the Rotary encoder until the desired sound is

obtained.

Setting the Dimmer Control

Press and hold FUNC.VIEW for at least 2 seconds so that

the  indicator lights up.

Press and hold 6DIMMER for at least 2 seconds

repeatedly to select the DIMMER mode.

DIMMER A (Auto mode)  DIMMER ON  DIMMER OFF 

DIMMER A

DIMMER A mode:

Decrease the illumination brightness of the blue button with the

head lights of the vehicle ON. This mode decreases the unit’s

backlighting at a certain extent at night.

DIMMER ON mode:

Keep the illumination brightness of the blue button dark.

DIMMER OFF mode:

Keep the illumination brightness of the blue button bright.

Press and hold FUNC.VIEW for at least 2 seconds to

activate the normal mode.

The  indicator goes out.

Notes

• Operate the unit while the  indicator lights up. If no operation is

performed for 5 seconds, the  indicator goes out.

• The function is inoperable when the ILLUMINATI is set to other than

TYPE1, refer to “Changing Lighting Colour” on page 22.

Listening to Radio

Press SOURCE to select TUNER mode.

Press BAND repeatedly until the desired radio band is

displayed.

F1 (FM1)  F2 (FM2)  F3 (FM3)  MW  LW  F1 (FM1)

Press TUNEA.ME to select the tuning mode.

DX SEEK (Distance mode)  SEEK (Local mode)  OFF (Manual

mode)  DX SEEK

Note

• The initial mode is Distance mode.

Distance mode:

Both strong and weak stations will be automatically tuned in

(Automatic Seek Tuning).

Local mode:

Only strong stations will be automatically tuned in (Automatic

Seek Tuning).

Manual mode:

The frequency is manually tuned in steps (Manual tuning).

Press  or  to tune in the desired station.

Holding down  or  will change the frequency

continuously.

Presetting Stations Manually

While receiving the station that you want to store, press

and hold, for at least 2 seconds, any one of the preset

buttons (1 through 6) into which you wish to store the

station.

The display shows the band, preset number and station

frequency memorised.

Notes

• A total of 30 stations can be stored in the preset memory (6 stations for

each band; FM1, FM2, FM3, MW and LW).

• If you store a station in a preset memory which already has a station,

the current station will be cleared and replaced with the new station.

• If the  indicator is illuminated, turn off the indicator by pressing

and holding FUNC.VIEW for at least 2 seconds, and then you can

perform the operation.

Controllable with Remote Control

This unit can be controlled with an optional Alpine remote control.

For details, consult your Alpine dealer.

Point the optional remote control transmitter at the remote control

sensor.

Connectable to Remote Control Interface Box

With an optional Alpine Steering Wheel Remote Control Interface

Box (not included), this unit is controllable from the vehicles

steering wheel controls. For details, contact your Alpine dealer.

RESET switch

Remote control sensor

Radio





SOURCE/

TUNE/A.ME

BAND

FUNC./VIEW

Rotary encoder

Preset buttons

(1 through 6)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine CDE-135BT Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alpine CDE-135BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info