Bedienungsanleitung Cateye CC-GL50 (Seite 3 von 41) (Englisch)

538691

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

How to install the

unit on your bicycle

Setting up the

computer

How to use the

computer

Setup of your PC

Uploading the

measurement data

Changing the

computer

conﬁguration

OthersIntroduction

Procedure of automatic recognition

The computer automatically recognizes the sensor ID according to the following procedure.

Signals from each sensor (speed, speed/cadence, cadence, heart rate, and power) are

searched at the time when the GPS search screen displayed when the power is turned

on, or the standby screen is changed to the measurement screen.

Caution: Any sensor that is not sending the sensor signal at this time cannot be

recognized. Each sensor sends the sensor signal in response to the

following operations.

Sensor type Method

Speed sensor

Move the magnet close to the sensor zone

(at a distance of less than 3 mm)

Speed/cadence (ISC) sensor

* When using the CATEYE speed/ca-

dence sensor (ISC-11), select [ISC]

to perform paring.

Cadence sensor

Heart rate sensor Wear the heart rate sensor

Power sensor Ride the bicycle lightly

Among the pairing-performed IDs of each sensor, the sensor with the strongest signal

is received. The sensor signal icon corresponding to the received sensor appears on the

display, and measurement is started. Each sensor is displayed as follows.

Sensor type Display

Speed sensor

Speed/cadence (ISC) sensor

S and C ﬂash simultaneously

Cadence sensor

Heart rate sensor

Power sensor

* The computer performs measurement using the GPS signal when the speed signal from

the speed sensor or speed/cadence (ISC) sensor cannot be received. In such a case, the

computer changes to measurement using the speed sensor whenever the speed signal is

detected.

* When the cadence signal, heart rate signal, or power signal cannot be received, the rel-

evant measurement value is not displayed.

GPS

GPS (Global Positioning System) is a system to identify the current position on the earth by

receiving highly precise positional information sent from a satellite.

Receiving the GPS signal

• It may take several minutes to acquire the GPS signal after turning on the computer.

• While searching the GPS signal, we recommend that you do not move around until receiv-

ing the GPS signal. It may take more time to receive the GPS signal if you move around

while searching the GPS signal.

• Receiving the GPS signal becomes easier under such conditions that the sky is open and

the prospect for the satellites is good.

Where the GPS signal cannot be received

The unit may stop measurement or may not display appropriate measurements when the

GPS signal cannot be received in the following locations or environments.

• In a tunnel, underground and building, between high-rise buildings, under an elevated

structure and arcade, etc.

• In bad weather (snow, rain, etc.)

• Near a high-voltage line or a mobile telephone relay station.

• When the computer display does not face to the sky.

* The measurement results may differ slightly from the actual values, when the speed is

calculated based on the GPS signal.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cateye CC-GL50 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cateye CC-GL50

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info