Bedienungsanleitung Cateye CC-GL50 (Seite 36 von 41) (Englisch)

538691

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

Introduction

How to install the

unit on your bicycle

Setting up the

computer

How to use the

computer

Setup of your PC

Uploading the

measurement data

Changing the

computer

conﬁguration

Others

Troubleshooting

The following troubles are not due to failure.

See also “FAQ” in CATEYE Atlas™ (web) (http://www.cateyeatlas.com/qa/).

Troubles related to the computer

Trouble Check Items Remedy

When the power is

turned on,

(bat-

tery icon) ﬂashes, and

then no display ap-

pears.

–

Remaining battery capacity is

nearly zero. Charge the computer

according to the procedure in “How

to charge” (page 7).

The power is turned off

while riding.

–

The power is automatically turned

off in 10 minutes if no GPS signal

or speed signal is received. (Auto

power off)

No display appears

when pressing and

holding the

button

for 2 seconds.

Is the battery for the com-

puter empty?

Charge the computer according to

the procedure in “How to charge”

(page 7).

Incorrect data appear.

–

Follow the procedure in “When the

operation is unstable” (page 35).

Measurement cannot

be performed. (

S or

C does not ﬂash)

When the ANT+ speed sensor or speed/cadence (ISC) sensor is

used

Did you perform pairing

with the speed sensor or

speed/cadence (ISC) sen-

sor used?

Perform pairing (page 32).

Is the condition for mount-

ing the speed sensor or

speed/cadence (ISC) sen-

sor cleared?

Mount the sensor correctly by

referring to the instruction manual

supplied with your sensor.

Is the battery for the speed

sensor or speed/cadence

(ISC) sensor used up?

Replace with new batteries.

Trouble Check Items Remedy

Measurement cannot

be performed (

does not ﬂash, but

ﬂashes on the dis-

play).

When the ANT+ speed sensor or speed/cadence (ISC) sensor is

not used

Is it immediately after

turning on the power?

It may take about 2 to 3 minutes to

acquire the positional information

after receiving GPS signal.

Is the location or weather

suitable for receiving the

GPS signal?

GPS signal may not be received,

thus the unit may stop measure-

ment or may not display appropri-

ate measurements in the following

locations or environments.

• In a tunnel, underground and

building, between high-rise build-

ings, under an elevated structure

and arcade, etc.

• In bad weather (snow, rain, etc.)

• Near a high-voltage line or a

mobile telephone relay station.

• The computer display does not

face upward.

Is the unit installed so that

the computer display (an-

tenna) faces to the sky?

To receive GPS signal effectively,

install the unit so that the computer

display faces to the sky.

The measurement data

is wrong.

–

The unit may stop measurement or

may display different values from

the actual one depending on the

receiving status, since measure-

ment is based on the GPS when

the speed sensor or speed/cadence

(ISC) sensor is not used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cateye CC-GL50 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cateye CC-GL50

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info