BURP
BURP features allows the user to expel water from inside the speaker grille.
This is useful if the radio is dropped in the water which may become trapped
in the speaker grille and mufe the audio.
To activate BURP:
1. Press and release the MEM/ESC and Max Range
buttons at the same time.
2. The Burp tone(s) at maximum level will sound from
the internal speaker for 8 seconds. During this time,
BURP will appear in the display.
3. Hold the radio with the speaker grille down to help
the water drain out.
4. After an 8-second interval, the radio will return to
standby.
Tri-Watch Set-up
Your microTALK® radio can be set up to scan three of your favorite channels
for activity.
To Program or Edit the Tri-Watch Channels:
1. Press and hold the TRI-WATCH button from Standby
mode for two (2) seconds to activate Tri-Watch
Setup mode. The TW icon on the display will turn
ON.
2. Press Channel Up or Channel Down button to select
the desired Tri-Watch channel.
3. Press and release TRI-WATCH button to conrm
entry.
4. Repeat steps 2 and 3 to program the remaining
additional Tri-Watch memory channel.
5. After programming both Tri-Watch memory channels
the radio will immediately engage Tri-Watch mode.
Using Tri-Watch:
1. From Standby mode, press the TRI-WATCH button.
The TW will appear in the display along with the three
channels stored in the Tri-Watch memory.
2. The radio will scan through the three (3) Tri-Watch
memory channels.
3. A signal on any one (1) of the three (3) channels will
stop the scan for 6 seconds to allow you to listen
to the trafc on that location.
4. Press Channel Up or Channel Down button to
resume scanning the Tri-Watch channels or to
change the scan direction.
5. To EXIT the Tri-Watch scan, press the TRI-WATCH
button again, and the radio will return to Standby
mode.
Memory Scan
Your microTALK® radio can automatically scan the stored memory locations.
(See page 12 for setting memory locations)
To scan memory locations:
1. Make sure 2 or more memory locatios programmed
already.
2. Press and release the MEM/ESC button to enter
Memory mode from Standby mode. Memory icon
and the Memory Location show on the display.
3. Press and release the Scan button, then the Scan
icon will show on the display, and begin scanning
stored channel locations.
The Scan icon will continue to be displayed when
Memory Scan is On.
Your radio will continue to scan memory locations and
stop as an incoming transimmision is detected. Your
radio will remain on that stored channel/privacy code for
6 seconds.
Privacy Code Scan
Your microTALK® radio can automatically scan the Privacy Codes (either
CTCSS 01 through 38 or DCS 01 through 83) within one channel. Only one set
of privacy codes (CTCSS or DCS) can be scanned at a time.
To scan privacy codes:
1. While in Standby mode, press and release the Scan
button twice (CTCSS) or three times (DCS)until the
CTCSS or DCS icon and numbers are ashing.
2. Press and hold the Scan button to begin scanning
privacy codes within the selected channel.
The Scan icon will continue to be displayed when privacy code scan is on .
Your radio will continue to scan privacy codes and stop as an incoming
transmission is detected. Your radio will remain on that channel/privacy code
for 6 seconds.
During scanning (while receiving an incoming transmission), you can
choose from the following:
a. Press and hold the Talk button to communicate on that channel/privacy
code. Your radio will remain on that channel/privacy code and return to
Standby mode.
b. Press the Channel Up or Channel Down button to resume scanning
privacy codes. If you do not press any button within 10 seconds, your
radio will automatically resume scanning privacy codes.
c. Press the Scan button to return to Standby.
Channel Scan
Your microTALK® radio can automatically scan channels.
To scan channels:
1. Press and release the Scan button until the Scan
icon and the channel numbers appear on the display.
2. Press and hold the Scan button to begin scanning
channels.
The Scan icon will continue to be displayed when scan
is on . Your radio will continue to scan all channels and
stop if an incoming transmission is detected. Your radio
will remain on that channel for 6 seconds.
During scanning (while receiving an incoming transmission), you can
choose from the following:
a. Press and hold the Talk button to communicate on that channel. Your radio
will remain on that channel and return to Standby mode.
b. Press the Channel Up or Channel Down button to resume scanning
channels.
c. Press and hold the Scan button to return to Standby.
Roger Beep Conrmation Tone
Your listener will hear an audible tone when you release the Talk button. This
alerts the other party that you are nished talking and it is OK for them to
speak.
To turn roger beep on or off:
1. Press the Mode/Power button until the Roger Beep
icon ashes. The current on or off setting is
displayed.
2. Press the Channel Up or Channel Down button to
select roger beep on or off .
3. Choose one of the following:
a. Press the Mode/Power button to enter the new
setting and proceed to other functions.
b. Press Talk or Call button to return to Standby mode.
c. Do not press any buttons for 12 seconds to return to
Standby mode.
Key Tone On/Off
When Key Tone is On , an audible tone will sound each time a button is
pressed.
To turn key tone on or off:
1. Press the Mode/Power button until the keytone icon
Flashes. Current key tone status On/Off will ash.
2. Press the Channel Up or Channel Down button to
select key tone on or off.
3. Choose one of the following:
a. Press the Mode/Power button to enter the Standby
mode.
b. Press Talk or Call button to return to Standby mode.
c. Do not press any buttons for 12 seconds to return to
Standby mode.
Ten Call Tone Settings
You can choose between ten different Call Tone Settings to transmit a call
alert.
To change a call tone setting:
1. Press the Mode/Power button until the letter “C” and
the current call tone number (01 through 10) is
displayed. The current call tone will sound for three
seconds.
2. Press the Channel Up or Channel Down button to
hear the other call tone settings.
3. Choose one of the following:
a. Press the Mode/Power button to enter the new
setting and proceed to other functions.
b. Press Talk or Call button to return to Standby mode.
c. Do not press any buttons for 12 seconds to return to
Standby mode.
VibrAlert® and Call Alert
Your MicroTALK® radio can alert you to incoming signals
by sounding an audible call tone or an audible tone with
VibrAlert® .
To change call settings:
1. Press the Mode button until the Call Setting icon
ashes on the display. The current setting (“01”
vibrate + ring, “02” ring only) is displayed.
2. Press the Channel Up or Channel Down button to
change the call setting.
3. Choose one of the following:
a. Press the Mode button to enter the new setting and
proceed to other functions.
b. Press Talk or Call button to return to Standby mode.
c. Do not press any buttons for 12 seconds to return to
Standby mode.
MEM
ESC
SCAN
MAX
RANGE
TR
W
Call Tone
R
X
V ox
TW DCS Scan
CTCSS Mem
BURP P ow er Sa v er
T
Call Tone
Vibrate On
R
X
V ox
TW DCS Scan
CTCSS Mem
BURP P ow er Sa v er
T
Call Tone
Vibrate Off
(conti nued)
Using
Using
MEM
ESC
TRI
WA
SCAN
MEM/ESC Button
T
Channel Button
T
Channel Button
T
Channel Button
T
Channel Button
T
Channel Button
T
Channel Button
T
Channel Button
T
Channel Button
CALL
MODE
Mode/Power
CALL
MODE
Mode/Power
CALL
MODE
Mode/Power
Tri-Watch Button
TR
W
Tri-Watch Button
TR
W
Tri-Watch Button
TR
W
Tri-Watch Button
H
SCAN MAX
RANGE
Scan Button
H
SCAN MAX
RANGE
Scan Button
H
SCAN MAX
RANGE
Scan Button
MEM
ESC
TRI
WA
SCAN
MEM/ESC Button
Trademark
CEEL™ is a registered trademark of Cobra Electronics Europe, Ltd.
Snake design and microTALK® are registered trademarks of Cobra Electronics
Corporation, USA.
Warranty & Customer Service
For warranty and customer service information, please contact your dealer.
For use in EU countries, subject to local laws and regulations.
©2019 Altis Zenus BV in the Netherlands
Wassenaarseweg 57,
2596CL The Hague
Niederlande/ Netherlands
We, the company Altis Zenus BV in the Netherlands
Wassenaarseweg 57,
2596CL The Hague
Niederlande/ Netherlands
declare under our sole responsibility that the following product
Type of product: Walkie Talkie
Trademark: Cobra
Model: AM1035 FLT
Further details: battery operated, 446MHz
meets the essential requirements of the following EU-Directives:
2014/53/EU Directive on the making available of radio equipment on the market
2011/65/EU Annex II amending Annex (EU)2017/2102
Directive on the restriction of the use of certain hazardous substances in
electrical and electronic equipment
applied standards and regulations:
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
EN 50566:2013
EN 300 296 V2.1.1
EN 301 489-1 V2.1.1 EN 301 489-5 V2.1.1
IEC 62321-3-1:2013 IEC 62321-4:2017
IEC 62321-5:2013 IEC 62321-6:2015
IEC 62321-7-1:2015 IEC 62321-7-2:2015
IEC 62321-8:2017
Authorized person for technical documentation:
Name, Position: Jaap Derk Buma, Director
The Hague, 30-7-2018
……………… …………………………..
Date Signature
Declaration of Conformity (DoC)
If “oF ” ashes in place of the privacy code numbers, a privacy code
is already set in the opposite (CTCSS or DCS) system. Press the
Channel Up or Channel Down button to cancel the opposite code
and select a privacy code from the active system for the selected
channel.
7. Choose one of the following:
a. Press the MEM/ESC button to enter the channel/privacy code in the
selected memory location. Radio then proceeds to next memory location,
which will blink.
b. Press and hold the MEM/ESC button to save the current state of the Set
Memory Function and press the MEM/ESC button again return to Standby
mode.
Note: If not press any button for 12 seconds, it will enter memory recall mode
automatically.
To recall a stored memory channel location:
1. Press the MEM/ESC button, the Memory icon and the
memory location number show on the display.
2. Press the Channel Up or Channel Down button to
select a memory location (0 through 9).
Press and hold the Talk button to communicate with
another person as usual
3. Press and hold the MEM/ESC button to return to
Standby mode on the selected memory location.
If a
its associated
shown on
A memory location can be reprogrammed at
any time it is displayed. Press the
MEM/ESC button to begin.
CTCSS Mem
Memory Channel
Roger Beep
Keytone icon
The radio ignores specic privacy
codes while scanning channels.
Scan
Scan Channels
Scan
Select Channel
Scan Privacy Co des
The main c han nel nu mb er w ill ash to
ind icate chan nel posi tion
TW
Tri-Watch Mode
After the Tri-Watch scan stops to monitor a
channel, as long as you do not press any buttons
within 6 seconds, your radio will automatically
resume scanning the Tri-Watch channels
MEM/ESC Button
BURP
BURP Icon
16 17 18 14 15
22 23 20 21
CTCSS
Vox
Standy By
