Bedienungsanleitung DeWalt D712N T 3 (Seite 17 von 20) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546147

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH

• Set your saw to the prescribed angles and make a few trial cuts.

• Practice fitting the cut pieces together.

• Example: To make a 4 sided box with 25° exterior angles (angle

“A”) (fig. S2), use the upper right arc. Find 25° on the arc scale.

Follow the horizontal intersecting line to either side to get the mitre

angle setting on the saw (23°).

Likewise follow the vertical intersecting line to the top or bottom to

get the bevel angle setting on the saw (40°). Always try cuts on a

few scrap pieces of wood to verify the settings on the saw.

Cutting Base Mouldings

The cutting of base moulding is performed at a 45° bevel angle.

• Always make a dry run without power before making any cuts.

• All cuts are made with the back of the moulding laying flat on the

saw.

INSIDE CORNER

Left side

• Position the moulding with top of the moulding against the fence.

• Save the left side of the cut.

Right side

• Position the moulding with the bottom of the moulding against the

fence.

• Save the left side of the cut.

OUTSIDE CORNER

Left side

• Position the moulding with the bottom of the moulding against the

fence.

• Save the right side of the cut.

Right side

• Position the moulding with top of the moulding against the fence.

• Save the right side of the cut.

Cutting Crown Mouldings

The cutting of crown moulding is performed in a compound mitre.

In order to achieve extreme accuracy, your saw has pre-set angle

positions at 31.62° mitre and 33.85° bevel. These settings are for

standard crown mouldings with 52° angles at the top and 38° angles

at the bottom.

• Make test cuts using scrap material before doing the final cuts.

• All cuts are made in a left bevel and with the back of the moulding

against the base.

INSIDE CORNER

Left side

• Top of the moulding against the fence.

• Mitre right.

• Save the left side of the cut.

Right side

• Bottom of the moulding against the fence.

• Mitre left.

• Save the left side of the cut.

OUTSIDE CORNER

Left side

• Bottom of the moulding against the fence.

• Mitre left.

• Save the left side of the cut.

Right side

• Top of the moulding against the fence.

• Mitre right.

• Save the right side of the cut.

GROOVING (FIG. T)

Your saw is equipped with a grooving stop (12) and grooving depth

adjustment knob (15) to allow for groove cutting.

• Flip the grooving stop (12) towards the front of the saw.

• Adjust the grooving depth adjustment knob (15) to set the depth of

the groove cut. It might be necessary to release the lock nut (66)

first.

• Place a piece of scrap material of approx. 5 cm between fence and

workpiece in order to perform a straight groove cut.

DUST EXTRACTION (FIG. A2 & A5)

This machine is provided with a dust extraction point (24) for connection

of a dust extraction kit (36) (available as an option).

WARNING! Whenever possible, connect a dust extraction

device designed in accordance with the relevant regulations

regarding dust emission.

Connect a dust collection device designed in accordance with the

relevant regulations. The air velocity of externally connected systems

shall be 20 m/s +/- 2 m/s. Velocity to be measured in the connection

tube at the point of connection, with the tool connected, but not

running.

CUTTING SMALL PIECES (FIG. J1)

The upper part of the left side of the fence (3) can be adjusted to

provide maximum support when cutting small pieces.

• Put the saw blade into vertical position.

• Loosen the plastic knob (29) at least 3 full turns.

• Adjust the fence as close to the blade as possible.

• Tighten the knob securely.

SUPPORT FOR LONG PIECES (FIG. A4)

• Always support long pieces.

• For best results, use the legstand (35) to extend the table width of

your saw (available from your dealer as an option). Support long

workpieces using any convenient means such as saw-horses or

similar devices to keep the ends from dropping.

TRANSPORTING (FIG. A6, B)

WARNING: Never use the guards to lift or transport the

saw.

In order to conveniently carry the tool, a carrying strap can be attached

to the base. The carrying strap (see fig. A6) is available as an option.

• To transport the saw, lower the head and depress the lock down

pin (14).

• Lock the rail lock knob with the saw head in the front position, lock

the mitre arm in the right mitre angle, slide the fence (3) completely

inward and lock the bevel lever (11) with the saw head in the

vertical position to make the tool as compact as possible.

• Always use the hand indentations (30) shown in fig. B to transport

the saw.

MAINTENANCE

Your DEWALT power tool has been designed to operate over a long

period of time with a minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of injury, turn unit off

and disconnect machine from power source before

installing and removing accessories, before adjusting

or changing set-ups or when making repairs. Be sure

the trigger switch is in the OFF position. An accidental start-

up can cause injury.

Lubrication

This machine requires no additional lubrication. The bearings of the

motor are pre-lubricated and watertight.

• Avoid using oil or grease as this can cause clogging with

sawdust and chips and create problems.

• Clean the parts subject to accumulation of sawdust and chips

periodically with a dry brush.

DeWalt D712N T 3 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info