Bedienungsanleitung Dremel DSM20 (Seite 13 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

488591

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Paddle switch with “Lock-OFF” feature

The Paddle switch enables the operator to control the switch

functions of “LOCK-OFF”, and “ON/OFF”.

To unlock switch and turn tool “ON”: Push “LOCK-OFF” switch

release lever forward to unlock paddle switch, then squeeze

paddle switch. PICTURE 7

To switch tool “OFF”: Release pressure on paddle lever.

The switch is spring loaded and will return to “OFF” position

automatically.

PICTURE 7

A. “Lock ON” button

B. “Lock OFF” switch release lever

C. Paddle switch

“LOCK-ON” button

The “LOCK-ON” feature, incorporated into the paddle switch, is a

convenience for long operations.

To lock switch “ON”: After paddle switch has been activated

push “LOCK-ON” button at rear of tool completely in and release

paddle switch. PICTURE 7

To switch tool “OFF”: Squeeze and release paddle switch.

In order to try to avoid recoil (a situation where the wheel wants

to skip out of the material) it is recommended to make cuts in the

same direction as the rotation of the wheel.

WARNING

IT IS IMPORTANT TO READ AND

UNDERSTAND THE SECTION IN THIS

MANUAL CALLED “KICKBACK AND RELATED WARNINGS”.

Depth adjustment

Disconnect plug from power source. Loosen the depth adjustment

lever located on the right side of the tool. The foot is spring

loaded and will lower automatically. PICTURE 8

Tighten lever counter clockwise at the depth setting desired.

Check desired depth.

PICTURE 8

A. Depth adjustment lever

B. Depth scale

Line guide

The cutting guide notch will give an approximate line of cut. Make

sample cuts in scrap lumber to verify actual line of cut.

PICTURE 9

A. Line guide

General cut offs

Maintain a firm grip and operate the switch with a decisive

action. Never force the tool. Use a light and continuous pressure

PICTURE 10

WARNING

AFTER COMPLETING A CUT AND THE

SWITCH HAS BEEN RELEASED, BE AWARE

OF THE NECESSARY TIME IT TAKES FOR THE WHEEL TO COME

TO A COMPLETE STOP DURING COAST DOWN. DO NOT SET

THE TOOL DOWN UNTIL THE ACCESSORY HAS COME TO A

COMPLETE STOP.

1. Make sure material being cut is secured in a vise or fixture

before attempting to cut

2. Keep your body positioned to either side of the wheel, but

not in line with the wheel. It is important to support the tool

properly and to position your body such as to minimize body

exposure from possible wheel binding and recoil.

3. Grip the tool firmly while cutting and always be ready and

able to manage the cut.

4. Avoid jamming, twisting or pinching the wheel with the

workpiece of otherwise applying excessive side pressure to

the wheel.

Cutting tile

Make sure material being cut is secured in a vise or fixture before

attempting to cut.

Turn the tool on and wait for the wheel to reach full speed. For

cuts that extend to the edge of a tile, cut all the way through

edge(s) along your cut line.

Score the tile first along your cut line, making multiple passes to

progressively cut through the tile.

This tool does not use wheels designed for face-grinding. If your

cut requires a smooth, finished edge, use an appropriate tile

finishing tool to refine the tile edge.

Plunge or interior cuts

The size and versatility of the Dremel DSM20 make it an excellent

option for making plunge or interior cuts into a workpiece such as

flooring, paneling, or siding.

1. Mark the surface to be cut with the desired cut lines

2. Loosen the Depth Adjustment Lever so that the spring loaded

foot releases and goes to the zero depth setting. Leave the

Depth Adjustment Lever loose during this cut.

3. Rest the Foot of the tool on the workpieces and Align the

tool’s wheel with the cut line. PICTURE 11

4. While holding the tool firmly, Press the Paddle Switch and

allow the tool’s wheel to come up to full speed.

5. Slowly plunge/lower the tool and wheel into the workpiece.

PICTURE 12

6. Guide the tool forward and complete the cut

7. Release the Paddle Switch and allow the tool to come to a

complete stop.

8. Remove the tool from the workpiece.

9. Repeat steps 3-8 as required to complete your cuts.

Flush cutting

First, consider the desired height of the flush cut. For flooring

installation, add up the thickness of your flooring adhesive, the

flooring itself, and any underlayments or other material that will

add to the thickness of the finished floor.

1. Install the flush cutting wheel on the tool as described in

“Flush Cutting Wheel Assembly”.

2. Adjust the depth of the wheel to the desired depth setting.

3. Turn the tool on it’s side so that the flush cut foot rests

against the flooring.

4. Firmly grip the tool. Turn tool on and allow it to come to full

speed before entering workpiece.

5. Complete your cut and remove the tool from the workpiece

before turning the tool off. PICTURE 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dremel DSM20 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info