Bedienungsanleitung Faber Hemmet (Seite 8 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

706554

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

- 2 -

Installation Instructions

Before installing this appliance, we recommend that;

1. You have your chimney cleaned by a competent

chimney sweep.

2. You block o the chimney  ue.

This procedure is important for the e cient operation

of the heating unit and will also reduce heat loss up the

chimney.

Installation.

Ensure that all packing items are removed (read any

warning labels carefully).

Retain all packing for possible future use, in the event

of moving or returning the appliance to your supplier.

To install the appliance;

1. Remove the  replace grate, ashpan etc.

2. The ashbed grate should be stored away for possible

future use.

3. Clean the hearth of any ash residue or dust etc.

At the rear of the appliance, two adjustable supports are

provided for levelling, where the base of the  replace

opening is raised above the level of the hearth.

You are now ready to install the electric  re into your

 replace.

Make sure the unit is switched OFF.

Hold the  re by the sides of surround and gently

manoeuvre into position. Plug the  re into a 13amp/240

volt outlet. Ensure that the supply cable exits at the front

of the  re, at the right or left hand corner to suit your

supply socket location and is not trapped under the  re

such that it might cause it to be damaged.

Before using the manual controls  rstly  ll the water

tank (See ‘Maintenance’, ‘Filling the water tank’).

Manual Controls.

The Opti-myst Manual controls are located beneath the

hinged canopy cover. Raise the canopy cover to access the

controls. (See Fig. 2 for Manual Control lay out)

Switch ‘A’:- Controls the electricity supply to the heater.

Note: This switch must be in the ‘ON’ ( I ) position for the

heater to operate with or without heat.

Switch ‘B’:- Controls the function of the  re.

Press

once to turn on  ame e ect. This will be

indicated by one beep.

Although the main lights operate immediately it will

take a further 30 seconds before the  ame e ect starts.

Press again to give  ame e ect and half heat.

This will be indicated by two beeps.

Press

again to give  ame e ect and full heat. This

will be indicated by three beeps.

Press

again to return to  ame e ect only.

This will be indicated by one beep.

Press to put  re in to standby mode.

This will be indicated by one beep.

Control Knob ‘C’:- Controls the intensity of the  ame

e ect.

Turning the control knob Clockwise increases the  ame

e ect, turning the control knob Anti Clockwise will

decrease the  ame e ect.

Control Knob ‘D’:- Controls the Electronic Thermostat

setting.

Turning the control knob Clockwise will decrease the

temperature setting, turning the control knob Anti

Clockwise will increase the temperature setting.

When the water is empty the main lamps go out. See

instructions under ‘Maintenance’, ‘Filling the water tank’.

When this procedure is complete, the main lamps will

illuminate but it will take 30 seconds before the  ames

return.

Electronic Thermostat

The thermostat controls the heat output according to

the room temperature. This ensures that the heater

will not produce heat unnecessarily when the room is

warm.

To set the temperature you require, turn the thermostat

control knob ‘D’ (See Fig. 2) Anti-Clockwise until the

desired temperature is reached. Alternatively to heat

a cold room quickly, turn the thermostat control knob

‘D’ (See  g. 2) up fully. When the room has reached the

desired temperature, turn the thermostat control knob

‘D’ (See Fig. 2) clockwise until the desired heat setting is

achieved.

The heater will now automatically operate at this

temperature.

Remote Control Operation

On the control panel, Switch A (see Fig. 2) must be in the

‘ON’ ( I ) position in order for the remote control to operate.

There are 3 buttons on the remote control. (See Fig. 7)

To operate correctly the remote must be pointed towards

the front fuel e ect.

The remote control functions are as follows:

Press once to turn on Flame e ect only.

This will be indicated by one beep.

Press once to turn on Half heat and Flame e ect.

This will be indicated by two beeps.

Press again to turn on Full heat and Flame e ect.

This will be indicated by three beeps.

Standby

This will be indicated by one beep.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber Hemmet Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info