Bedienungsanleitung Faber Hemmet (Seite 9 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

706554

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

- 3 -

Battery Information.

1. Unclip the battery cover on the back of the remote

control. (See Fig. 7)

2. Install AAA batteries into the remote control.

3. Replace the battery cover.

Discard leaky batteries.

Dispose of batteries in the proper manner according to

provincial and local regulations.

Any battery may leak electrolyte if mixed with a di erent

battery type, if inserted incorrectly, if all the batteries are

not replaced at the same time, if disposed of in a  re, or if

an attempt is made to charge a battery not intended to be

recharged.

Thermal safety cut-out

A thermal safety cut-out is incorporated in the fan heater

to prevent damage due to overheating. This can happen if

the heat outlet was restricted in any way or if the chimney

 ue has not been blocked o e ectively. If the cut-out

operates, unplug the heater from the socket outlet and

allow approximately 10 minutes before reconnecting.

Before switching the heater back on remove any

obstruction that may be restricting the heat outlet, then

continue normal operation.

Tips for using your appliance.

1. Only pull out the drawer when its time to re ll the

water tank or change a lamp, otherwise it may lead to

excess water in the sump and reduced  ame e ect.

If this happens empty the water from the sump as

instructed under ‘Maintenance’.

2. With the  ame setting on minimum the unit will use

approximately 40ml of water per hour and will last

3 times as long than when it is at maximum  ame

setting.

3. Do not tilt or move the  re while there is water in the

tank or sump.

4. Make sure that the  re is on a level  oor.

5. The  ame control knob ‘C’ Fig. 2 may be turned up or

down to give a more realistic e ect.

6. Sometimes the  ames appear more real when the  ame

control knob is turned down.

7. Give the  ame generator some time to react to

changes you may make on the  ame control knob.

Maintenance

WARNING: ALWAYS DISCONNECT FROM THE POWER

SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE

Changing lamps.

If a large amount of the smoke appears grey or colourless

it may be that one or more lamps have failed.

You can check for lamp failure as follows.

1. Leaving the  ame e ect on, gently pull the drawer fully

out by the tab. (See Fig. 3)

2. View the lamps from a distance in front of the  re and

observe which lamp needs to be changed.

3. Put Switch ‘A’ in the ‘OFF’ position, and unplug the  re

from the mains.

4. Leave the appliance for 20 minutes to allow the lamps

to cool down before removing them.

5. Remove the water tank by lifting upwards and place in

a sink.

6. Remove the sump as described in the Cleaning Section.

7. Remove the defective lamp, by gently lifting vertically

and disengaging the pins from the lamp holder, (See

Fig. 4 and 5). Replace with a Dimplex Opti-myst, 12V,

50W, Gu5.3 base, 8° beam angle, coloured lamp.

(Purchased from www.dimplex.co.uk under the section

‘After Sales Service’, details of how to purchase the

lamps are contained therein.)

8. Carefully insert the two pins of the new lamp into the

two holes in the lamp holder. Push  rmly in place. (See

Fig. 4 and 5).

9. Replace the Sump and water tank and carefully close

the drawer.

10. Switch on.

Filling the water tank.

When the water tank is empty,  ame and smoke e ect

shuts o , and you will hear 2 audible ‘beeps’. Follow these

steps to re ll:

1. Press Switch ‘A’ to (0) (See Fig. 2)

2. Gently pull out the drawer as far as possible by the tab.

(See Fig. 3)

3. Remove the water tank by lifting upwards and

outwards.

4. Place the water tank in sink and remove cap, Anti-

clockwise to open. (See Fig. 6)

5. Fill tank with  ltered tap water only. This is necessary

to prolong the life of the  ame and smoke producing

unit.

The water should be  ltered through a conventional

domestic water  lter unit and the  lter should be

replaced regularly.

6. Screw the cap back on, do not overtighten.

7. Return the tank to the sump, with the tank cap facing

down and the  at side of the tank facing outward.

8. Gently push the drawer back in as far as it will go.

9. Press Switch ‘A’ to ‘ON’ ( I ) position (See Fig. 2)

10. Press Switch ‘B’ once to turn on  ame e ect. (See

manual control section and Fig. 2)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber Hemmet Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info