Bedienungsanleitung Futaba FP6VA (Seite 3 von 8) (Englisch)

30084

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Switches and knobs

9. Elevator -> flap mixing switch (ELV -> FLP)

When this switch if pulled forward, the mixing function is

turned on and the flaps are linked with elevator operation.

However, this switch is effective only when elevator -> flap

mixing is active (ACT).

10.

Flap knob (FLAP)

Normally, this knob is used as CH6. When flaperon mixing is

active (ACT), this knob acts as the flap trimmer.

11. aileron dual rate switch (AILERON D/R)

This switch toggles the aileron servo travel (RATE1 ,

RATE2). RATE1; upper position RATE2; down position

12. Elevator dual rate switch (ELEVATOR D/R)

This switch toggles the elevator servo travel (RATE1,

RATE2). RATE1; upper position RATE2; down position

13. Landing gear switch (GEAR)

This switch activates the landing gear channel. (CH5 switch)

14.

Power switch

The transmitter is turned on when this switch is set to the

upper position.

15. Trainer switch (TRAINER)

This switch is turned on when set to the pulled forward posi-

tion (spring-loaded type).

Others

16. Level meter

[!] This meter indicates the transmitter power supply voltage.

When the needle deflects to the boundary between the silver

and red ranges, recharge the Nicd battery.

17.

Hook

Hook for neck strap.

18.

Antenna

[!] When using the transmitter, extend the antenna to its full

length.

19.

Carrying bar

Use this handle to carry the transmitter.

20. Battery cover

Open this cover when adjusting the trimmers on the trimmer

panel and when changing the Nicd battery.

21. Charging jack

This is the transmitter Nicd battery charging jack.

(Charging the Nicd battery)

[!] Never try to charge a dry cell battery. It will cause the battery

to overheat or explode and is very dangerous.

[!] Always charge the Nicd battery before using your R/C set.

Connect the charger's transmit-

ter and receiver connectors to

the transmitter charging jack and

receiver servo Nicd battery as

shown in the figure(FIG.2). The

charging LEDs light to show that

the battery is being charged.

* The normal charging time is

about 15 hours. When you have

not used your R/C set for some

time, repeatedly charge and dis-

charge the batteries two or three

times before use.

* The transmitter and receiver Nicd batteries can be charged

simultaneously or independently.

(Non-slip adjustable lever head)

The length of the lever head

of the sticks can be adjusted

as desired. Adjust the stick

length to fit your hand. (FIG.3)

1) Unlock lever heads A and B

by turning them in the direc-

tions shown by the arrows.

2) Adjust the stick to the most comfortable length and lock it by

turning head B in the directions opposite that shown by the

arrow.

(Stick lever spring tension adjustment)

The stick lever spring

tension can be adjusted

by removing the trans-

mitter back cover and

turning the screw for

each stick as shown in

the figure (FIG.4). Adjust

the spring tension for the

best stick feel. When ad-

justing the stick spring,

set the throttle stick to the

center.

(Trimmer panel)

a. Servo reversing switch (SERVO REVERSER)

The servo reversing switches reverse the direction of travel of

the servos. The lower position is the normal position.

(Channels 1 to 6) (DIP switch Nos. 1 to 6)

b. Mode switches

1. Elevator -> flap mixing ACT/INH switch

To activate the mixing function, set this switch to the ACT

(upper) position. To deactivate the mixing function, set this

switch to the INH (lower) position. (DIP switch No. 7)

2. Flaperon mixing ACT/INH switch

To activate the mixing function, set this switch to the ACT

(upper) position. To deactivate the mixing function, set this

switch to the INH (lower) position. (DIP switch No. 8)

3. Rudder AST function ACT/INH switch

To activate the rudder and throttle AST functions, set this

switch to the ACT (upper) position. The throttle ATV func-

tion can be activated by setting this switch to the INH

(lower) position. Select the desired function.

c. Aileron dual rate trimmer (AIL D/R)

This trimmer sets the rate corresponding to both directions of

the aileron dual rate switch. (RATE1, RATE2)

When it is turned clockwise, the servo travel increases.

d. Elevator dual rate trimmer (ELV D/R)

This trimmer sets the rate corresponding to both directions

the elevator dual rate switch. (RATE 1, RATE2)

When it is turned clockwise, the servo travel increases.

Throttle

AST

trimmer

(TH.AST) or throttle

ATV

trimmer

(TH.ATV) H side

This trimmer adjusts the servo travel of the selected function.

When it is turned clockwise, the servo travel increases.

f. Rudder AST trimmer (RUD.AST) or Throttle ATV trimmer

(TH.ATV) L side

This trimmer adjusts the servo travel of the selected function.

When it is turned clockwise, the servo travel increases.

g. Aileron differential trimmer (DIFF.RATE)

This trimmer adjusts the aileron differential amount when the

flaperon mixing function is active.

h. EIevator -> flap mixing trimmer (ELV->FLP)

This trimmer adjusts the mixing operation direction and

amount.

i. Flap trimming function trimmer (FLP.TRIM)

This trimmer adjusts the flap trimming operation direction and

variation width when the flaperon mixing function is active.

-3-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP6VA Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info