Bedienungsanleitung Futaba FP6VA (Seite 6 von 8) (Englisch)

30084

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

of the TH.ATV trimmers on the trimmer panel. Adjust the

high side travel to between high side trimmer positions 0

(30%) and 10(100%).

* Low side travel adjustment:

Adjust the low side travel with the low side trimmer (L) of

the TH.ATV trimmers on the trimmer panel. Adjust the

low side travel between low side trimmer positions 0

(30%) and 10(100%).

Throttle AST function

(Function)

This function sets the throttle servo travel. In this case,

the high side and low side can be adjusted simulta-

neously. Use this function to compensate for throttle

linkage variation. The travel rate can be adjusted from

30% to 100% of the total servo travel as shown in the

figure.

(Adjustment)

To activate the throttle AST function, set the rudder AST

(RUD.AST) ACT/INH switch (DIP switch No. 9) on the

trimmer panel to the ACT (upper) position. (The rudder

AST function can be used simultaneously, but the throttle

ATV function cannot be used simultaneously.)

* Travel adjustment:

Adjust the servo travel with the TH.AST trimmer on the

trimmer panel. Adjust the travel rate between throttle

AST

trimmer positions 0 (30%) and 10 (100%).

Rudder AST function

(Function)

This function adjusts the rudder servo travel. In this case,

the left and right travels can be adjusted simultaneously.

Use this function in rudder linkage correction. The travel

rate can be adjusted from 30% to 100% of the total servo

deflection angle as shown in the figure.

(Adjustment)

To activate the rudder AST function, set the rudder AST

(RUD.AST) ACT/INH switch on the trimmer panel to the

ACT position. The throttle AST function can be used si-

multaneously, but the throttle ATV function cannot be

used simultaneously.)

* Travel adjustment:

Adjust the servo travel with the RUD.AST trimmer on the

trimmer panel. Adjust the travel to between rudder AST

trimmer positions 0 (30%) and 10 (100%).

Throttle trim lever with ATL function

(Function)

As shown in the figure, when the throttle stick is set to the

maximum slow side, the throttle trim influence is also at

it's maximum. When the throttle stick is in the high side

the throttle trim has no influence. This greatly simplifies

throttle linkage adjustment. (The high side linkage

should be set first.)

7)After connecting the linkages and checking the operating

directions and amounts, start the engine and adjust the

engine needle, then fly the airplane and trim the servos.

2. Aileron/elevator dual rate (D/R) function

(Function)

The maximum travel of the aileron and elevator servos can

be altered by operating their respective dual rate switch.

For instance, when the switch is in the down (RATE2) posi-

tion, the deflection angle is the normal deflection angle.

When the switch is set to the upper (RATE1) position, spins,

snap rolls, and other aerobatics that require a maximum de-

flection angle can be performed by adjusting the deflection

angle to an angle greater than the normal deflection angle.

Since the respective rates can be adjusted by setting the

switch to the upper and down positions, the direction of the

switch can be set as desired.

(Switch operation)

The aileron dual rate switch (AILERON D/R) is at the front top

right side of the transmitter. The upper position is RATE1 and

the down position is RATE2.

The elevator dual rate switch (ELEVATOR D/R) is at the front

top left side of the transmitter. The upper position is RATE1

and the down position is RATE2.

(Rate adjustment)

Each rate can be adjusted with the RATE1 and RATE2 trimmers

on the trimmer panel behind the battery cover at the back of the

transmitter. The rate can be adjusted from 30% (position 0) to

100% (position 10) of the maximum deflection angle.

(Setting procedure)

1) Turn on the transmitter and receiver power.

2) Switch the dual rate switch of the channel you want to the posi-

tion for the rate that you want to set.

3) Set the stick to the maximum travel in either

direction.

4) Using the trimmer, adjust the servo horn to the desired angle.

(Adjust each rate by repeating steps 1 through 4.)

* When not using the dual rate function, set the RATE1

and

RATE2 trimmers to 100% (fully clockwise).

3. Flaperon mixing

(with aileron differential function)

-6-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP6VA Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info