Bedienungsanleitung Hitachi c10ra (Seite 34 von 38) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

382435

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

English

(4) Drill a 8 mm hole in each location marked (Fig. 3).

(5) Replace the table saw.

Using suitable length four 50 mm botls, nuts, and flat

washers (not provided) secure the table saw to the

workbench, cabinet or stand.

ASSEMBLY PROCEDURES

WARNING

⅜ To avoid an accident or personal injury, always

confirm that the switch is turned OFF and the power

plug has been disconnected from the receptacle

before assembly of this tool.

1. Assembly of Handle Bar

The handle bar allows faster turning of the wheel.

(1) Tighten the screw of the handle bar until it hits against

the wheel.

(2) Securely tighten the handle bar nut with a wrench

(Fig. 4).

2. Assembly of Rip Fence

CAUTION

⅜ The rip fence must be aligned parallel to the saw

blade to minimize the kickback.

The rip fence can be conveniently used to cut a

workpiece into different pieces of precise width

or into parallel pieces. It can be mounted on either

the right or left side of the table.

(1) Align the groove in the front of the table with the

groove in the fence bracket and slide it in the direction

indicated by the arrow from the end of the table (Fig.

5).

(2) Attach clamp handle (A) to the screw of fence bracket.

(3) When moving the rip fence, loosen clamp handle (A)

to release the lock. To lock the rip fence, tighten clamp

handle (A).

3. Assembly of Miter Gauge

The miter gauge is convenient for cutting long or

angular pieces which are difficult to work on with the

rip fence.

It can be mounted on either the right or left side of

the table.

Align the sheet bar of miter gauge with the table

groove and slide it in the direction indicated by the

arrow through the front of the table (Fig. 6).

4. Mounting and adjusting Saw Blade Guard

CAUTION

⅜ The saw blade guard and riving knife must be

aligned properly to the saw blade in order to

prevent kickback.

(1) Mounting the riving knife

1 Turn the wheel fully clockwise and set the saw

blade to the maximum cutting height (Fig. 7).

2 Loosen the saw blade tilt lock handle and move

the saw blade tilting mechanism to the right until

it hits against the stopper.

Then tighten the saw blade tilt lock handle.

3 Remove the table insert on the table.

4 Mount the riving knife to the bracket using the

wrench, 6 × 16 mm bolt, spring washer, flat washer

and two shims (Fig. 8).

NOTE

⅜ Make certain the two protrutions are engaged with

the slot in the riving knife.

(2) Mounting the saw blade guard

Mount the saw blade guard to the riving knife using

the 6 mm Cap Hd. Sq. Neck Bolt, flat washer and 6

mm special nut (Fig. 9).

(3) Adjusting the riving knife

1 Use a straightedge to align the riving knife with

the saw blade (Fig. 10).

NOTE

⅜ The shims can be relocated or be removed as

needed to center the riving knife over the saw

blade.

2 Check clearance between saw blade tip and the

riving knife.

It should be less than 5 mm at all positions (Fig.

11).

If not, loosen the 6 × 16 mm bolt securing the riving

knife to the bracket.

Move the riving knife up and down. After

adjustment of the riving knife is complete, firmly

retighten the 6 × 16 mm bolt by wrench.

5. Mounting Elbow (Chip Extraction Duct) (Standard

Accessory)

Connect a 65 mm hose of dust collector to the chip

extraction duct to suck cutting chips away.

Mount the chip extraction duct on the chip discharge

outlet at the body rear of the body (Fig. 2).

6. Assembly of Extension Wings (Standard Accessory)

(1) Use a straightedge to ensure the extension wings are

level with the table surface (Fig. 12).

(2) Assembling the extension wings using the three 6 ×

20 mm bolts (with/washer) (Fig. 13).

(3) Adjust the tables so that the rip fence receiving groove

at the table front is level with the rip fence receiving

groove on the extension wings. The extension wings

must be the same level as the table. If it is not same

level, loosen 6 × 20 mm bolts (with/washer) and

readjust the extension wings.

(4) Mount the extension supporter while using the

straightedge to make sure that the table surface is

level with the surface of extension wings.

Tighten the four 8 × 20 mm bolts (Fig. 13).

7. Assembly of Table Saw Stand (Optional Accessory)

Assemble it with the stay and leg(s).

(1) Set the stays below and assemble the legs outside.

(2) Secure with 8 mm cap hd. sq. neck bolts and nuts

(Fig. 14).

(3) Then attach rubber caps underneath the legs (Fig. 14).

ADJUSTMENT

This tool is accurately adjusted before shipping from the

factory. Check the following accuracies and readjust them

if necessary in order to obtain the best results in

operation.

WARNING

⅜ To avoid an accident or personal injury, always

confirm that the switch is turned off and the power

plug has been disconnected from the receptacle

before adjustment of this tool.

1. Adjusting 90° and 45° positive stops

This tool is equipped with positive stops for rapid and

accurate positioning of the saw blade at 90° and left

bevel 45° to the table. Check and adjust the positive

stops by the following procedures.

(1) To adjust positive stop at 90°.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi c10ra Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info