Bedienungsanleitung Hitachi c10ra (Seite 35 von 38) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

382435

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

English

The pointer should indicate 90° on the protracter scale

on the miter gauge.

(2) If the pointer does not point to 0 on the miter gauge,

1 Tighten clamp handle (B).

2 Loosen the 5 mm machine screw on the sheet bar.

3 Adjust the pointer to the 90° position and tighten

the 5 mm machine screw on the sheet bar.

PRACTICAL APPLICATIONS

1. Switch Operation

To turn the saw on, press the green button.

To turn the saw off, press the red button.

2. Overload protective device for motor

When the motor becomes overload, the overload

protective device cuts off the current to stop the motor.

In this case, push the reset button (after few minute

later).

3. Raising and lowering saw blade

CAUTION

⅜ Adjust the saw blade height so it is about 3.2 mm

above the top of the workpiece.

Raising the saw blade much higher than the

workpiece does not make it cut better. It is unsafe

and provides less table surface in front of the saw

blade.

Never operate while saw blade rotating.

(1) Raising saw blade.

Grasp the wheel and rotate it clockwise to raise the

saw blade (Fig. 7).

(2) Lowering saw blade.

Grasp the wheel and rotate it counterclockwise to

lower the saw blade (Fig. 7).

4. Saw Blade Tilting Operation

WARNING

⅜ The saw tilt lock handle must be locked during all

cutting operations.

(1) Loosen saw blade tilt lock handle.

(2) Push in wheel until teeth on hub of hand wheel

engauge with segment gear.

(3) Turn wheel to tilt the saw blade to the desired angle

and tighten saw blade tilt lock handle (Fig. 17).

5. Rip Fence Operation

CAUTION

⅜ Make sure that the rip fence is always in parallel

with the groove on the table.

(1) Loosen clamp handle (A).

(2) Move the rip fence right and left while pressing the

fence bracket against the table surface and set the

desired distance from the saw blade (Fig. 5).

(3) Tighten clamp handle (A) to lock the rip fence.

6. Miter Gauge Operation

CAUTION

⅜ For bevel cutting (the saw blade is tilted), use the

miter gauge in the right side groove to prevent

hands or miter gauge from interfering with the saw

blade guard.

(1) Loosen clamp handle (B).

(2) Turning the miter gauge to the desired angle.

(3) Tighten clamp handle (B) to lock the miter gauge (Fig.

21).

1 Turn the wheel fully clockwise and set the saw

blade to the maximum cutting height (Fig. 7).

2 Use a square to check the saw blade is at a precise

90° (Fig. 15).

3 If the saw blade is not at a precise 90°, loosen the

6 mm machine screw (A) a few turns and move

the saw blade until the blade is at 90° to the table

(Fig. 16).

4 Loosen the 5 mm machine screw and set the

needle pointer to 0°.

(2) To adjust positive stop at left bevel 45°.

1 Turn the wheel fully clockwise and set the saw

blade to the maximum cutting height (Fig. 7).

2 Loosen the saw blade tilt lock handle and move

the saw blade to the left (Fig. 17).

Then tighten the saw blade tilt lock handle.

Use a 45° gauge to check the saw blade is at a left

bevel 45° (Fig. 18).

If the saw blade is not at a left bevel 45°, loosen

the 6 mm machine screw (B) a few turns and move

the saw blade until the blade is at left bevel 45° to

the table (Fig. 16).

2. Adjustment of rip fence

The edge of the rip fence should then line up parallel

with the miter gauge groove.

If the edge of the rip fence is not parallel with the miter

gauge groove,

1 Loosen the two 6 mm bolts securing the parallel

bracket to the fence bracket (Fig. 19).

2 Loosen the clamp handle (A), align the rip fence

parallel to the groove, and tighten the clamp

handle (A).

3 While holding the parallel bracket to prevent

movement, tighten the two 6 mm bolts previously

loosened.

4 Loosen the clamp handle (A), move and return the

parallel bracket adjacent to the groove, tighten the

clamp handle (A) and verify that the parallel

bracket is parallel to the groove.

5 Repeat adjustment until it is parallel.

6 After adjustment, tighten two 6 mm bolts.

3. Adjustment of pointer

The pointer should indicate the accurate distance from

the saw blade.

NOTE

⅜ The pointer will need to be readjusted whenever

a different thickness saw blade is installed.

To adjust pointer 0 setting.

(1) Loosen clamp handle (A) and move the rip fence to

bring it into tight contact with the side of the saw blade

(Fig. 20).

(2) Make sure that the point points to 0 on the scale

provided on the table.

(3) If the pointer does not point to 0 on the scale,

1 Tighten clamp handle (A).

2 Loosen the 5 mm machine screw holding the

pointer.

3 Adjust the pointer to the 0 position and retighten

the 5 mm machine screw.

4. Adjustment of Miter Gauge

The miter gauge should be squareness to the saw

blade.

To adjust pointer 0 setting.

(1) Loosen the clamp handle (B) and place a square

against both the saw blade and miter gauge (Fig. 21).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi c10ra Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info