Bedienungsanleitung Hitachi c10ra (Seite 36 von 38) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

382435

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

English

OPERATING INSTRUCTIONS

Ripping requires the use of the rip fence and cross cutting

uses the miter gauge.

CAUTION

⅜ Always use eye protection when working with the tool

to prevent eye injury.

⅜ Also, use a face mask for additional safety and wear a

dust mask if the cutting operation produces dust.

1. Ripping

Cutting operation

1 Adjust the saw blade height so it is about 3.2 mm

above the top of the workpiece.

2 Hold the workpiece flat on the table and against

the rip fence.

Keep the workpiece about 25 mm away from the

saw blade.

CAUTION

⅜ The workpiece must have a straightedge against

the rip fence and must not be warped, twisted or

bowed.

Keep both hands away from the saw blade and

away from the path of the saw blade.

3 Turn on the switch on and allow the saw blade to

come up to speed.

4 Keeping the workpiece against the table and rip

fence, slowly feed the workpiece rearward all the

way through the saw blade. Continue pushing the

workpiece until it is clear of the guard and it falls

off the rear of the table.

CAUTION

⅜ Do not push the free piece that is cut off, merely

guide it.

⅜ When the width of rip 50 mm to 152 mm wide,

use a push stick to feed the workpiece. (Push stick

is standard accessory)

⅜ When the width of rip is less than 50 mm wide,

use an auxiliary guide a push block.

WARNING

⅜ Never operate to pull the workpiece back with the

saw blade turning.

2. Bevel Ripping

This operation is the same as ripping except that the

bevel angle is set to an angle other than 0°.

WARNING

⅜ Only work with the workpiece and rip fence on

the right side of the saw blade.

3. Cross Cutting

Cutting Operation

1 Adjust the saw blade height so it is about 3.2 mm

above the top of the workpiece.

2 Hold the workpiece firmly against the miter gauge

with the path of the saw blade in line with the

desired cut distance.

Keep the workpiece about 25 mm away from the

saw blade.

CAUTION

⅜ Keep both hands away from the saw blade and

away from the path of the saw blade.

3 Turn the switch on and allow the saw blade to

come up to speed.

4 While keeping the workpiece against the face of

the miter gauge, and holding the workpiece flat

against the table, slowly push the workpiece

through the saw blade.

WARNING

⅜ Never operate to pull the workpiece back with the

saw blade turning.

4. Bevel Ripping

Cutting Operation

This operation is the same as cross cutting except that

the bevel angle is set to an angle other than 0°.

WARNING

⅜ Only operate with the workpiece and miter gauge

on the right side of the table.

5. Mitering

Cutting Operation

This operation is the same as cross cutting expect that

the miter gauge is locked at an angle other than 90°.

WARNING

⅜ Hold the workpiece firmly against the miter gauge

and feed the workpiece slowly into the saw blade

to prevent the workpiece from moving.

6. Compound Mitering

Cutting Operation

This is a compound of bevel cross cutting and

mitering.

It is infrequently used. Follow the instruction for both

bevel cross cutting and mitering.

MOUNTING AND DISMOUNTING SAW BLADE

WARNING

To prevent an accident or personal injury, always turn off

the switch and disconnect the power plug from the

receptacle before removing or installing a blade.

1. Mounting the saw blade

(1) Turn the wheel fully clockwise and set the saw blade

to the maximum cutting height (Fig. 7).

(2) Tighten the saw blade tilt lock handle and lock the

saw blade at 90°.

(3) Remove the table insert on the table.

(4) Mount the washer (A), saw blade and washer (A) in

this order on the saw blade spindle. (The saw blade

with the teeth pointing down at the front of the table.)

(5) Using the open end wrench and place the wrench on

the flats on the saw blade spindle. Hold the saw blade

spindle from turning and tighten nut using the

remaining wrench (Hex. Wrench) by turning the set

nut clockwise (Fig. 22).

(6) Replace the table insert on the table.

WARNING

⅜ Be sure to grip set nut carefully with the wrench.

A serious injury can be sustained, if your grip

should slip, the wrench come off the nut, and your

hand strike the sharp blade edges.

⅜ When mounting the saw blade, confirm that the

rotation indicator mark on the saw blade and the

rotation direction of the saw are properly matched.

⅜ Tighten the set nut so it does not come loose

during operation.

Confirm the set nut has been properly tightened

before the power tool is started.

2. Dismounting the saw blade

Dismount the saw blade by reversing the mounting

procedures described in paragraph 1 above.

CAUTION

⅜ Never attempt to install saw blades larger than

255 mm in diameter. Always install saw blades that

are 255 mm in diameter or less.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi c10ra Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info