Bedienungsanleitung Jablotron CU-07 (Seite 2 von 3) (Englisch)

554982

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

CU-07 Tracer unit 2/2 MKW51102

parts of this unit are initialized during these approx. 2 minutes of

flashing. If the unit is connected to the power supply for the first

time after its purchase, the slow flashing changes to rapid

flashing after the two minutes, indicating that the unit is waiting

for configuration. When the unit has received its configuration

(from your tracer service provider) it sends a confirmatory SMS

reporting the successful setting to the number from which it was

configured. The unit is now ready for journey recording

Solving problems which might occur during primary

configuration:

I have not received a confirmatory SMS, even though the

whole process was carried out in conformity with the

instructions. Solution: try to repeat the process.

The unit’s LED indicator has started flashing SOS in Morse

code (3 dots, 3 dashes, 3 dots). Solution: a unit or SIM card

failure has been detected, contact the tracer service provider.

2. Advanced unit configuration

Advanced unit configuration increases the convenience

and functionality of the whole monitoring system. The

configuration can be carried out via SMS messages sent to

the unit’s telephone number.

Each SMS must begin with a six-digit number (the default

number is 123456). The manufacturer recommends

changing this password, see 2.1. The password should be

followed with a comma and then one or more commands

separated with other commas. The SMS must not exceed 160

characters.

2.1. Access password change

The manufacturer recommends changing the password. Be

careful when changing the password; if you forget it, it is

impossible to restart the unit to default settings. In such a

case contact the manufacturer.

Command format: Password,MCxxxxxxxxxxxx

where: xxxxxx is a new access password for the device

(the 6 characters should be repeated twice, only digits

can be entered)

Command example:

123456,MC654321654321 (the new password will be 654321)

2.2. Entering drivers’ telephone numbers

If the unit is installed in a vehicle which is used by multiple

drivers, it is possible to set the number of the driver who is going

to drive the vehicle easily by dialling into the unit from the

driver’s telephone. The device memory can hold telephone

numbers of up to 15 drivers who can identify themselves by

dialling into the unit. The telephone number can consist of 12

digits maximum and it must be entered in the international

format.

Command format: Password,TELx+yyyyyyyyyyyy

where: x – the unit’s reference number of the telephone

number (from 1 to 15);

yyyyyyyyyyyy – telephone number in international

format (max.12 digits excluding the «+» sign)

Example of a command programming numbers of drivers 1 and

2: 123456,TEL1+420608234567,TEL2+420777654321

Format of the command to erase a telephone number:

Password,TELx+0

Example of a command to erase driver 1’s telephone number:

123456,TEL1+0

Note: One SMS can contain multiple commands; the password

is only stated at the beginning of the SMS.

2.3. Driver selection by dialling in

A driver can assign himself to a journey by dialling into the unit

from his telephone if his number is recorded in the unit’s

memory (see 2.2). The unit terminates the call automatically and

the driver who has called into the unit is set for all the following

journeys until another driver dials in.

2.4. Driver selection by an SMS command

A driver can also be selected with an SMS command (e.g. a

function for a dispatcher). In order to change the current driver’s

number you have to enter the following command:

Command format: Password,Dxx

where: xx – the two-digit number of a driver (01 to 15)

Command example:

123456,D02 (to set driver 2)

2.5. Journey type setting

If you need to differentiate between various journey types

(private, business, etc.), you can set it before the

commencement of a journey by sending an SMS. The device

enables classification into five journey types. The current

journey type can be selected by sending an SMS command.

The journey type can be changed via an SMS command

without a password, but only from telephone numbers

recorded in the unit (see 2.2.). In such a case the driver’s

number changes automatically together with the journey type.

Command format: Tхх

where: хх – journey type:

00 = business (default)

01 = private

02 = service

03 = foreign business (e.g. due to the price of fuel)

03 = foreign personal (e.g. due to the price of fuel)

Command example:

T01 (sets a private journey) and the driver

is changed according to the telephone number from which the

command was sent.

The journey type can also be changed using an SMS

command with a password. In such a case only the journey

type changes - the driver remains unchanged. This command

can also be sent from telephone numbers which are not

recorded in the given unit (function suitable e.g. for a

dispatcher).

Command format: Password,Tхх

where: хх – journey type (see above)

Command example:

123456,T01 (sets a private journey)

2.6. Journey termination timer setting

The device enables the setting of the time interval necessary for

journey termination. If we set the timer to 600 sec., then the unit

waits for vehicle motion detection for 10 minutes after the

journey termination. If the vehicle starts moving again, the

original journey continues. Otherwise the journey is terminated

and the unit switches to sleep mode.

Command format: Password,ETх

where х – number of seconds

permitted values: 200 s. - 5100 s. (85 min.)

default setting 300 s. (5 min.)

Command example: 123456,ET600 (time-out set for 10 min.)

2.7. SMS command reception confirmation

The device can confirm execution of the received SMS

commands based on the following parameter setting:

Jablotron CU-07 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info