Bedienungsanleitung Jablotron JA-65X (Seite 2 von 7) (Englisch)

554895

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

Digital communicator JA-65X 2/7 MFM53102

2.3 Voice message(s) recording

sequence: 8x

You can record two different voice messages (10 sec. each).

Depending on the setting in section 2.4, a particular message

will be sent under different situations. Recording of the

messages:

a) enter 85 on the keypad

b) press and hold push button on the X module

c) speak towards the module (max. 10 s)

d) release the button, message will play back

This results in the recording of message number 1. To record

message 2 enter 86 in step a)

If you prefer sending only one, but longer, message (20 sec.),

record message by entering 84 in step a). By programming as

described in section 2.4 you can specify which alarms will trigger

the sending of a message.

Notes:

• Make the messages brief and clear. The dialer repeats the message to

each called number for 40 seconds.

• The voice messages are stored in non-volatile memory and can be

changed when ever you want to by repeating the above steps.

• The existing messages can be played by momentarily pressing the push

button on the X module (or by entering F9 while in stand by mode).

2.4 Triggering of voice and SMS messages

sending sequences: 9 y x

With sequences 91x to 95x you can select which alarms will

trigger the telephone dialer to call and what will be sent.

Enter: 9 y x

where:

y Alarm x reaction

1 Panic – silent 0 no reaction

2 Intruder 1 voice1 and SMS

3 Fire 2 voice 2 only

4 Tampering 3 SMS only

5 Technical trouble

Notes:

• Final texts of alarm SMS are generated by the SMS server

(providers computer) – based on the digital code sent by

the alarm system (check with provider for more details)

• If only one long voice message was recorded by using code

84 as described in section 2.3, then this message will be

sent when x=1 or x=2

• Voice messages are sent step by step to all telephone

numbers programmed as described in section2.1

• SMS message is sent to a mobile phone number

programmed as described in section 2.2

Example: if the dialer should send an SMS and voice message

1 when intruder or panic alarm is triggered, voice message 2 in

the case of fire and only an SMS in the case of technical alarm,

enter: 911 921 932 943

Factory default setting: all alarms will trigger sending of voice

message 1 and SMS (911, 921, 931, 941, 951).

2.5 Dialing method

sequence: 9 0 x

Enter:

9 0 1 for tone dialing

9 0 0 for pulse dialing (this option is blocked for

some countries)

Note: this dialing method setting is also valid for Central

monitoring station communications.

Factory default: tone dialing

2.6 Telephone line checking

sequence: 9 9 x

If this function is enabled, the dialer will check regularly if the

telephone line is ready to make a phone call. If the line is not

ready for more than 15 minutes, the keypad will indicate a

telephone line failure (failure L). A non-working telephone line or

a phone conversation or Internet connection longer than 15

minutes can cause a fault.

options:

9 9 1 checking enabled

9 9 0 checking disabled

Note: this setting is also valid when the dialer is used for

Monitoring station communications as well as remote PC access

Factory default setting: checking disabled

2.7 Telephone dialer testing

sequence: 8 9

After entering code 89 the dialer will call all programmed numbers

and will play voice message 2. It will also send a SMS message if

programmed. The telephone line signals will be audible from the

control panel’s built in speaker during the test (if the dialer is

triggered by an alarm in normal operation, it will call silently).

If you prefer testing with voice message 1 enter code 88.

Testing can be terminated with the N key.

3 To enable a remote computer to dial in

When the user or installer wants to dial in to the installation

from their computer or a remote JA-60E keypad via a JA-60U

modem (see section 6), the following parameters should be

programmed.

The most convenient programming is via a connected PC

using the Comlink software. Programming can also be

performed manually:

• Enter the programming mode when disarmed (F 0

Service Code, factory default 6060), indicated by a ”P“

• Any unfinished programming sequence can be

terminated by the N key.

• To exit the programming, press the N key (“P“ will

turn off).

Dialing in parameters

Function sequence options factory d.

Incoming call reaction 0 5 x

0=never

1= second call

2-6 = after ring

No. 2 - No.6

disabled

Remote access code

(8 digits)

0 7

xxxxxxxx

any 8 digits

code

00000000

3.1 Reaction to an incoming call

sequence: 05

This sequence sets how the communicator will react to incoming

calls on the telephone line. This setting is important for remote

access. Enter:

0 5 x

where: x = 0 - never answer

1 - answer after second call = after 1 or 2 rings are

detected, there must be a pause of 10 - 45

seconds. The dialer will then answer on the very

first ring of the second call. This setting can be

used to bypass an answering or facsimile

machine connected to the same line. This

“Second Call” feature is supported by the

Comlink software and also by the JA-60E

keypad.

2 to 6 - answer after 2

to 6

ring

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-65X Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info