Bedienungsanleitung Jablotron JA-65X (Seite 4 von 7) (Englisch)

554895

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

Digital communicator JA-65X 4/7 MFM53102

• The Surgard protocol has 4/2 structure plus one more digit

which is generated automatically (see 4.3)

• If the control panel is split and only one section is armed,

then a partial arming report code is sent. If all sections are

armed, a complete arming report code is sent. If the

system was completely armed and only one section is

disarmed, the disarming report code will be sent and then

it will be followed by the partial arming report code.

• The pulse formats are not capable to report zero and

numbers above 15. For this reason events in zone 16 or in

a subsystem are reported to the Monitoring Station as

events in zone 10. This means that from the point of view

of the monitoring station zone 10 also covers zone 16 and

the subsystem if used. This problem does not exist in the

CID protocol.

• If the system is arming while there is a bypass, partial

arming will be reported to the CMS (also stored to the

internal memory)

Factory setting: 00 for all events

4.2 Account ID code setting

sequence: 02

This sequence is used for the alarm system identification by a

Monitoring Station. The sequence structure: 02 x x x x

where:

xxxx – account ID code ( x are numbers from 0 to 9 or

hexadecimals).

When using only three-digit codes (formats 3/1 and 3/2) enter

a zero in the first position. The communicator will then ignore it

(example - 0123)

Note: Changing of the account code erases the internal

communicator’s memory of non reported events and sends a

„Reset“ reporting code (051) to the Monitoring Station. If pulse

formats are used, zero is transmitted as A

Factory setting: 0000

4.3 Protocol and Format setting

sequence: 03

This sequence is used to select the communication protocol

and format. Its structure is as follows: 03 x y

where:

x - protocol (0 – 9, see table bellow)

y - format (0 - 3 see table on right)

Notes:

• Some Monitoring Station receivers do not support all formats.

• Logic of the format marking - 4/2 means that an account code has

4 digits and an event report code has 2 digits.

• Changing of a format erases the internal communicator’s memory

of non reported events and sends a “Reset“ reporting code (051)

to the Monitoring Station.

Factory setting: 90 (Contact ID)

4.4 Re-dialing pause setting

sequence: 04

If a dialer is triggered it attempts to make a connection

(alternating between the primary and the backup telephone

number). If it is not possible to make a connection after 8

attempts, a pause is initiated. After this pause the dialer will

attempt again. If any event triggers the communicator during the

pause, the pause ends immediately. The pause length can be set

in the following way:

0 4 x

where:

x – time multiplied by 10 minutes (from 1 to 9, example 3 =

30 minutes)

Factory setting: 1 = 10 min.

4.5 CMS phone number entering

sequence: 06

Central monitoring station modem phone numbers can be

stored by entering the following sequence: 0 6 x x .... x F y

where:

xx...x = Central Monitoring Station phone number (up to

16 digits)

y = 1 for primary phone number memory

2 for back up phone number memory

Pause (3 sec.) can be inserted into the telephone number by

entering F0. It is also possible to insert the * tone by F7 or the

# tone by F8 if requested for DTMF dialing.

Example: number 02 123456 as main Monitoring Station

number is entered with 06 02 F0 123456 F1.

Phone number erasing: 0 6 F 0 F y

where:

y = 1 to erase the primary telephone number

2 to erase the back up telephone number

Protocols

x Name

Hand-

shake

Data Kiss off Speed

format

Ademco Slow

(Silent Knight)

1400Hz 1900Hz 1400Hz 10bps

table

Ademco Fast 1400Hz 1900Hz 1400Hz 14bps

table

Telemax 2100Hz 1650Hz 2100Hz 10bps

table

Franklin 2300Hz 1800Hz 2300Hz 20bps

table

Radionics 2300 2300Hz 1800Hz 2300Hz 40bps

table

Radionics 1400 1400Hz 1900Hz 1400Hz 40bps

table

DTMF 2300 2300Hz DTMF 2300Hz DTMF

table

Surgard* 2300Hz DTMF 2300Hz DTMF

4/3

Ademco express* Dual tone DTMF 1400Hz DTMF

4ID/2

Contact ID* Dual tone DTMF 1400Hz DTMF

CID

* fixed format, “y” is arbitrary (0 is recommended)

Formats

format reports structure

3/1

Major events only

xxx R

3/2

All events

xxx rc

4/1/1

Major events with autom. source

identification

xxxx Rn

4/2

All events

xxxx rc

xxxx = account number

R = major event code (only first digit counts)

rc = detailed event code (two digits)

n = source identification (generated automatically)

Surgard protocol has structure: xxxx E rc, where E is a group

identifier (generated automatically)

E Event Note

1 Fire

2 Panic

3 Alarm General

4 Arming Incl. Partial

5 Disarming

6 Failure Power failure, RF jamming …

8 Report Enter/Exit service mode …

9 Restore End of alarm, panic …

A Test 24 hour test

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-65X Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info