Bedienungsanleitung Jablotron JA-65X (Seite 3 von 7) (Englisch)

554895

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

Digital communicator JA-65X 3/7 MFM53102

Notes: Remote access connection can also be enabled by the

alarm system user (regardless of the above setting) by entering

89 while in the user mode, when the phone rings. If you use

another telephone set on the same telephone line, it should be

switched to the tone dial mode.

Factory setting: 0 = never answer

3.2 Remote access code setting

sequence: 07

In order to access the panel remotely, it is necessary to

authorize the access with an 8-digit access code. This code is

compared with the one programmed in the control panel. If the

caller tries to access the panel with another code, the

connection will be terminated immediately. A wrong code alarm

will be triggered on the control panel after the 5

unsuccessful

attempt to dial in. Store your access code to the control panel by

entering: 0 7 xxxxxxxx

where:

x x . . . . . x - any 8 digits access code

Factory setting: 00000000

4 Central monitoring station

communication setting

This part of the manual is intended only for specialists involved

in monitoring. We recommend to use a computer equipped with

Comlink program for complete setting of the monitoring station

communication.

Changes of the setting can also be performed manually using

the keypad:

• Enter programming mode when disarmed (F 0 Service

Code, factory default 6060), indicated by a “P“.

To exit programming press the N key (“P“ will turn off).

Central monitoring station communication parameters

Sequence Description Factory default setting

0 001 xx

0 198 xx

Reporting codes table (see part 5)

where: x= 0 – 9, F0 = A

, F1 = B

, F2 = C

, F3 = D

, F4 = E

, F5 = F

if 00 is set, the event is not reported

For all events

0 2 xxxx

Account ID code (4 digits, for 3/1 and 3/2 formats the structure is 0xxx)

x = 0 – 9 (hexadecimal codes can be used too - see above)

0000

0 3 xy Protocol x:

0 = Ademco Slow

1 = Ademco Fast

2 = Telemax

3 = Franklin

4 = Radionics

2300

5 = Radionics 1400

6 = DTMF 2300

7 = Surgard

8 = Ademco

Express

9 = Contact ID

Format y:

0 = 3/1 (xxx R)

1 = 3/2 (xxx rc)

2 = 4/1/1 (xxxx Rn)

3 = 4/2 (xxxx rc)

Contact ID

0 4 x Re-dialing pause, x= 1 – 9 (x 10 min.)

1 10 minutes

0 6 xx..xFy CMS phone numbers xx...x to memory y (1 and 2), pause = F0

erased

0 9 6060

Communicator reset to factory default settings

Notes:

Some of the protocols are not standardized and some

manufacturers of Monitoring Station receivers use different

parameters in some of their protocols. Therefore Jablotron

cannot guarantee full compatibility with all Central Monitoring

Station receivers.

If the connection with the Monitoring Station is not available,

the events are queued in the communicator’s memory and are

transmitted in one burst as soon as the connection is

established. All events are reported to the Monitoring Station in

the same order as they happened.

Once communication has started, it can not be interrupted

unless the control panel is switched to the programming or to

the user mode. For example, if the user causes a false alarm

and then cancels it, both events are sent to Monitoring Station.

Events occurring while the control panel is in the

programming or user mode are reported to the Monitoring

Station after the closing of these modes. (They are stored in

the memory and reported together with reporting codes

describing the change of operation modes.)

When the dialer is activated, the communication to the

monitoring station has the highest priority (voice and SMS

messages are sent later with lower priority). A User or Installer

can interrupt the digital dialer communication by entering the

User mode or Programming mode. Reset of the control panel

has no influence to the digital communicator’s settings (it is

reported to the Monitoring station as an event).

The RESET of the digital communicator itself (sequence 0

9 6060), the change of the Monitoring Station’s telephone

numbers, the change of an account number code or the

change of a format setting will erase all the reporting codes

queued in the communicator’s memory. However the events

remain stored in the control panel’s internal memory.

Jablotron recommends use of the MS-350 monitoring

station with ComGuard SW.

4.1 Reporting codes setting

sequences: 00 and 01

These sequences can be used to program the report codes for

all possible events. Depending on the used protocol and

format, different amounts of data should be entered. The

complete report code programming table is shown in section 5.

The setting sequence structure is as follows: 0 x x x r c

where:

xxx = event number (from 001 to 198)

rc = report code (two digits). For 3/1 and 4/1/1 formats

only the first digit of the report code is used (R).

Codes should be entered in a hexadecimal

format, with numbers higher than 9 beginning

with the F key: A

= F0 B

= F1 C

= F2 D

F3 E

= F4 F

= F5

If the reporting code 00 is programmed, the event will not be

reported to the Monitoring Station.

Notes:

• Abbreviation "Rc" is used in the report code programming

table for the major events group. Only the first digit of this

group of codes is transmitted when formats 3/1 or

4/1/1are used. Other formats use both digits of the "Rc"

and "rc" report codes.

• The Contact ID (CID) is an automatic protocol. If you enter

any report code other than zero for a major event (Rc), all

events of this type will be transmitted automatically

including all details regarding the event source. Internal

structure of the CID protocol is shown in part 1.1. This

protocol provides the most in-depth data for the monitoring

station and its use is recommended by Jablotron.

Jablotron JA-65X Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info