Bedienungsanleitung Jablotron JA-80V (Seite 7 von 10) (Englisch)

555056

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

The JA-80V LAN/PSTN line communicator - 7 - MKA51202

5.10. Initialization of GSMLink communication

After successfully connecting the communicator to the LAN network

913 should be entered to initialise communication to the

www.GSMLink.cz

server (the server will register the IP address of the

communicator).

To access the system remotely via the Internet it is necessary to

(after communication has been

initialised). To register the system (see 7.5) you will need the

communicator registration code, which is printed on the label which

you will find on the communicator board.

Note:

• the communicator reports regularly to the GSMLink server to update

the communicator’s IP address in the server database (the period of

the regular reports is more frequent the more frequently GSMLink

access is used). If you try to access the alarm system via GSMLink

after the communicator’s dynamic IP address has changed, you can

be notified by GSMLink that it is necessary to wait for the next

regular communication from the system. To shorten this waiting time

you can enter the above sequence (913) on the system keypad

while in service mode or you can do it remotely by calling the

communicator from a phone, whose number was programmed for

this purpose (see the following text).

5.10.1. Tel. number to initialise GSMLink communication

GSMLink communication can be initialised remotely by calling (ringing)

from a phone number which can be programmed by:

914 xx...x ∗0 where xx...x = phone number (max. 20 digits)

Notes:

• After the first ring from the above programmed number the

communicator will report to GSMLink to update its IP address,

• this remote way of initialisation is only possible if the phone line

used by the communicator supports CLIP caller ID recognition).

Factory default setting: erased

5.11. Tx SMS center telephone number

To send SMS by CLIP protocol via the telephone line it is necessary to

program the Tx SMS center telephone number by:

942 xx...x ∗0 where xx...x = Tx SMS center tel. number

Note:

• Contact your telephone line provider to learn the Tx SMS center tel.

number.

Factory default setting: erased

5.12. Rx SMS center telephone number

To receive SMS by CLIP protocol via the telephone line it is necessary

to program the Rx SMS center telephone number by:

942 xx...x ∗0 where xx...x = Rx SMS center tel. number

Note:

• Contact your telephone line provider to learn the Rx SMS center tel.

number,

• check also how to activate delivery of the SMSes in text form (some

providers convert SMS text into voice messages).

Factory default setting: erased

5.13. Testing reporting to an ARC

To test reporting to an ARC enter:

961a where a = ARC number (1 or 2)

Note:

The event code “Communication test” (ec=31) will be sent to the ARC.

The green LED flashes while the report is being sent, if the red LED

goes off it indicates that the report to the ARC was unsuccessful.

5.14. Testing calls to a phone number

To test that the communicator is capable of calling the phone numbers

programmed into its memories enter:

962M where M is the phone number memory 1 to 8

If memory M contains a phone number, this number will be called and

if the phone call is answered, there will be an acoustic signal.

5.15. Remote programming by the SMS instruction

Instruction PRG can be used to send programming and operating

sequences to the alarm system:

code_PRG_seq,seq,seq...

where:

code is valid access or service code (e.g. 8080 or 1234)

_ space

seq programming sequence usually set via the keypad

Note:

• In the sequence can be used characters 0 to 9, ∗ and #)

• When the valid instruction is received, communicator simulates

entering the keys on the keypad, comma in the SMS is taken as a

pause in the sequence entering

• System must be unset and switched to the service mode

• The number of sequences in one SMS is limited by the maximum size of

the SMS in the GSM network.

Example: by sending SMS 8080 PRG

∗

08080,201,# the exit delay will

be set to 10s

5.16. Triggering LAN re-login

After entering

935 the communicator will log out of the LAN network and

then re-log in (DHCP updates).

5.17. Communicator reset

Entering 98080 returns the communicator to its factory default settings and

texts, erases all telephone numbers and disables reporting.

5.18. Automatic DHCP

The factory default settings in the communicator expect automatic

DHCP in the LAN network. If you need to enter the network

parameters manually, the automatic DHCP should be disabled with

this sequence and network parameters should be entered manually by

the following sequences before the communicator is connected to the

LAN network.

9300 DHCP disabled

9301 DHCP enabled

Factory default setting: enabled

5.19. Communicator IP address

If DHCP is disabled (see 5.18) program the communicator IP address

by:

931 xxx xxx xxx xxx

where:

xxx…x is IP address

Example: if the IP address is 192.168.1.23 enter:

931 192 168 001 023

Factory default setting: 192.168.001.211

5.20. Network mask

If DHCP is disabled (see 5.18) program the network mask by:

932 xxx xxx xxx xxx

where:

xxx…x is the network mask

Example: if the network mask is 255.255.255.0 enter:

932 255 255 255 000

Factory default setting: 255.255.255.000

5.21. Network gateway address

If DHCP is disabled (see 5.18) program the network gateway by:

933 xxx xxx xxx xxx

where:

xxx…x is the gateway address

Jablotron JA-80V Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info