Bedienungsanleitung Jablotron JA-80V (Seite 6 von 10) (Englisch)

555056

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

The JA-80V LAN/PSTN line communicator - 6 - MKA51202

Factory-default SMS report and instruction texts

n Factory text n Factory text n Factory text n Factory text

Report from your

alarm:

Device

332

Code

503

Fire

Device

333

Code

504

Panic alarm

Device

334

Code

505

Invalid code-entries exceeded

Device

335

Code

506

Alarm when power turned on

Device

336

Code

507

Tamper alarm

Device

337

Code

508

End of tamper alarm

Device

338

Code

509

End of alarm indication

Device

201

Control panel

339

Code

510

Alarm cancelled by user

Device

202

Service code

340

Code

511

Setting

Device

203

Annual inspection request

341

Code

512

Unsetting

Device

204

Communicator

342

Code

513

Partial setting

Device

205

Keypad

343

Code

514

Codeless setting

206

ARC code

Device

300

Master code

344

Code

515

External communication fault

Device

301

Code

345

Code

516

External comm. restored

Device

302

Code

346

Code

517

Fault

Device

303

Code

347

Code

518

Fault no longer present

Device

304

Code

348

Code

519

Mains dropout over 30 minutes

Device

305

Code

349

Code

520

Mains dropout

Device

306

Code

350

Code

521

Mains recovery

Device

307

Code

400

System status

522

Discharged battery

Device

308

Code

401

Set

523

Battery OK

Device

309

Code

402

Unset

524

Switching to Service Mode

Device

310

Code

403

Exit delay

525

Leaving Service Mode

Device

311

Code

404

Entrance delay

526

PGX

Device

312

Code

405

Alarm

527

PGY

Device

313

Code

406

Service mode

528

Radio jamming present

Device

314

Code

407

Maintenance mode

529

Internal communication fault

Device

315

Code

408

Partial setting

530

Internal comm. restored

Device

316

Code

409

Discharged battery

531

Communication test

Device

317

Code

410

Tamper alarm

532

Unconfirmed alarm

Device

318

Code

411

Alarm memory

601

SET

Device

319

Code

412

Fault

602

UNSET

Device

320

Code

413

Power fault

603

STATUS

Device

321

Code

414

Unknown status

604

MEMORY

Device

322

Code

415

Time:

605

PGX ON

Device

323

Code

416

Last event:

606

PGX OFF

Device

324

Code

417

Credit unknown

607

PGY ON

Device

325

Code

418

Credit:

608

PGY OFF

Device

326

Code

419

not used

609

AUX ON

Device

327

Code

420

Error while processing

command

610

AUX OFF

Device

328

Code

421

Output turned on

611

CREDIT

Device

329

Code

422

Output turned off

42 Device 330 Code 501 Instant alarm

43 Device 331 Code 502 Delayed alarm

Numbers 01 to 50 for devices and codes are

automatically generated by the communicator

so it is unnecessary to enter them in the text

• The communicator always automatically puts numbers from 01: to 50: in front of Device or Code names.

• Texts 0 to 532 are used to create SMS event reports

• Texts 601 and 611 are SMS instructions (to control the system remotely by SMS)

5.6. Phone number for instant remote access

A telephone number programmed with this sequence allows instant

remote access no matter what reaction to incoming calls is

programmed. If this number calls, the control panel will answer the call

after the first ring (the telephone line must provide CLIP protocol caller

ID for this feature).

902 xx...x ∗0 where xx...x = phone number

Note:

• if remote access is disabled (see 5.7), then using this phone number

for remote access is also disabled.

Factory default setting: erased

5.7. Remote access

Remote access (by phone or Internet) can be enabled or disabled:

9030 disabled

9031 enabled

Factory default setting: enabled

5.8. Forwarding of incoming SMS messages

This feature enables the automatic forwarding of incoming SMS

messages which contain no valid instructions to the system:

9260 messages are not forwarded (will not be used)

9261 messages are forwarded to the first programmed tel.

number in memories M1 to M8 (e.g. if numbers are only

programmed in M5 and M6, then messages will be

forwarded to M5). The tel. number from which the SMS

was received will be shown at the beginning of the

forwarded text.

Factory default setting: messages are forwarded

5.9. Reaction to incoming calls

The communicator’s reaction to incoming phone calls can be set by:

904 x

where

x = 0 incoming calls are ignored

x = 1 to 8 the communicator will answer after x multiplied

by 5 seconds of ringing (e.g. x=4=20sec.)

x = 9 answers after a second call - first there must be

at least one ring, then a pause (10 to 45sec.) and

then just after the first ring of the second call, the

call will be answered

Factory default setting: 9045 – answers after 25 sec. (about 5 rings)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-80V Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info