Bedienungsanleitung Jablotron JA-80Y (Seite 4 von 12) (Englisch)

555058

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

The JA-80Y GSM communicator - 4 - MFJ55304

Automatic SIM card credit

interrogation

Credit balance checking is set by SMS instruction code_CREDIT_uu..u_xx_yyy_zz where uu..u =

instruction for the GSM network (e.g. ∗101# etc.), xx= period in days, yyy=minimum balance, zz=

the position in which the number showing the balance starts, If the reported credit balance is lower

than the set limit (yyy), the credit balance message from the provider will be forwarded to phone

numbers M1 and M8

Programming by SMS

System can be programmed remotely via SMS instruction code PRG seq, seq,... where seq is

programming sequence set also from the keypad (e.g. 8080 PRG ∗08080,201,# set the 10s exit

delay)

Triggering re-registration to the

GSM network

923

The communicator will unregister from the GSM network and then re-register. Also possible via

the SMS instruction: code GSM. Code = master, user or service code

Communicator reset 98080 Resets to the factory default settings and erases all phone numbers, text will not be changed

Memorizing the SIM card’s PIN

code in the communicator

920 xx..x ∗0

xx..x = new PIN, sequence 920∗0 erases the

PIN (to use a SIM card with a disabled PIN)

erased

Configuring the GPRS log-in

parameters*

by SMS instruction to the alarm system: code GPRS x..x,y..y,z..z where code = master or service code, x..x =

the APN, y..y = name, z..z = password (only enter the APN if the name and password are not required by the

GSM provider)

ARC main tel. number/IP address

01 a xx..x ∗0

ARC backup tel. number/IP

address

02 a xx..x ∗0

a=1=ARC1, a=2=ARC2, xx..x = tel. number

(max.20 digits) or IP address & port – for

example: 01 2 ∗8 192 168 001 123 08080 ∗0

(∗8= signifies an IP address, it must have 12

digits followed by a 5 digit port number).

Entering 01p∗0 or 02p∗0 will erase the

number/address

erased

Installation (alarm system) ID for

ARC use

03 a zz..z ∗0

a=1=ARC1, a=2=ARC2, zz..z = ID number

max. 8 digits 0 to 9 and ∗1=A to ∗6=F

(hexadecimal number)

0000

Selecting the ARC protocol 04 a x

a=1 ARC1, a=2 ARC2

x=0 CID, x=1 SMS CID, x=2 IP CID

CID

Selection of events to report to

ARCs

05 a ec x

a=1 ARC1, a=2 ARC2

ec event code (see 5.27)

x=1 report, x=0 no report

all events are reported

Defining the delay before data is

resent to an ARC

06 a x

a=1 ARC1, a=2 ARC2

x=0 to 9 min. (0=immediately, without delay)

1 minute

ARC communication checking

period

(The time to wait after the last report

before performing an ARC

communication check)

07 a hhmm

a=1 ARC1, a=2 ARC2

hhmm = hours and minutes after last report

2400 (24 hours after last report)

Enable ARC reporting (ARC2

backs up ARC1)

00 a x

a=1 ARC1, a=2 ARC2

x=0 reports disabled, x=1 reports enabled, x=2

(only for ARC2) = ARC2 backs up ARC1

ARC reporting disabled

Recording reports sent to ARCs in

the control panel memory

08 x

x=0 no (only records ARC communication

faults, if communication checks are enabled)

x=1 yes (all reports except communication

checks)

yes

Indicate an ARC communication

fault if a report is not successfully

received by an ARC within 110

sec of transmission.

09 x

x=0 no

x=1 yes

IP address for data transmission

013 xx..x ∗0

IP address and port in format – e.g..: 013

∗8 192 168 021 123 08080 ∗0 (∗8 mark IP

address which must contain 12 digits, followed by

5 digits for the port.. Entering 013∗0 IP erase the

setting

77.104.220.129 7070

(img.jablotron.com)

Locking the ARC settings

901 xx..x ∗0

xx..x = an installer-defined locking code (4 to 8

digits). Entering this code and then exiting

service mode will lock the ARC settings

901∗0 will erase the code (= permanently

unlocked)

Unlocked

Unlocking the ARC settings

900 xx..x ∗0

xx..x = the locking code used by sequence

901

ARC programming can be temporarily

enabled in service mode by entering this

sequence. It will then relock on exiting service

mode.

These parameters effect reporting to the ARC and it is impossible to change them if the ARC settings are locked.

* These parameters cannot be programmed from the system keypad, but they can be programmed by sending SMS instructions or by Comlink software.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-80Y Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80Y

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info