Bedienungsanleitung Jablotron JA-80Y (Seite 7 von 12) (Englisch)

555058

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

The JA-80Y GSM communicator - 7 - MFJ55304

Factory-default SMS report and instruction texts

n Factory text n Factory text n Factory text n Factory text

44 Device 332 Code 504 Panic alarm 0 Report from your

alarm:

45 Device 333 Code 505 Invalid code-entries exceeded

1 Device 46 Device 334 Code 506 Alarm when power turned on

2 Device 47 Device 335 Code 507 Tamper alarm

3 Device 48 Device 336 Code 508 End of tamper alarm

4 Device 49 Device 337 Code 509 End of alarm indication

5 Device 50 Device 338 Code 510 Alarm cancelled by user

6 Device 201 Control panel 339 Code 511 Setting

7 Device 202 Service code 340 Code 512 Unsetting

8 Device 203 Annual inspection request 341 Code 513 Partial setting

9 Device 204 Communicator 342 Code 514 Codeless setting

10 Device 205 Keypad 343 Code 515 External communication fault

11 Device 206 ARC code 344 Code 516 External comm. restored

12 Device 300 Master code 345 Code 517 Fault

13 Device 301 Code 346 Code 518 Fault no longer present

14 Device 302 Code 347 Code 519 Mains dropout over 30 minutes

15 Device 303 Code 348 Code 520 Mains dropout

16 Device 304 Code 349 Code 521 Mains recovery

17 Device 305 Code 350 Code 522 Discharged battery

18 Device 306 Code 400 System status 523 Battery OK

19 Device 307 Code 401 Set 524 Switching to Service Mode

20 Device 308 Code 402 Unset 525 Leaving Service Mode

21 Device 309 Code 403 Exit delay 526 PGX

22 Device 310 Code 404 Entrance delay 527 PGY

23 Device 311 Code 405 Alarm 528 Radio jamming present

24 Device 312 Code 406 Service mode 529 Internal communication fault

25 Device 313 Code 407 Maintenance mode 530 Internal comm. restored

26 Device 314 Code 408 Partial setting 531 Communication test

27 Device 315 Code 409 Discharged battery 532 Unconfirmed alarm

28 Device 316 Code 410 Tamper alarm 601 SET

29 Device 317 Code 411 Alarm memory 602 UNSET

30 Device 318 Code 412 Fault 603 STATUS

31 Device 319 Code 413 Power fault 604 MEMORY

32 Device 320 Code 414 Unknown status 605 PGX ON

33 Device 321 Code 415 Time: 606 PGX OFF

34 Device 322 Code 416 Last event: 607 PGY ON

35 Device 323 Code 417 Credit unknown 608 PGY OFF

36 Device 324 Code 418 Credit: 609 AUX ON

37 Device 325 Code 419 (internal use only) 610 AUX OFF

38 Device 326 Code 420 Error while processing command 611 CREDIT

39 Device 327 Code 421 Output turned on

40 Device 328 Code 422 Output turned off

41 Device 329 Code 501 Instant alarm

42 Device 330 Code 502 Delayed alarm

43 Device 331 Code 503 Fire

Numbers 01 to 50 for devices and

codes are automatically generated by the

communicator so it is unnecessary to

enter them in the text

• The communicator always automatically puts numbers from 01: to 50: in front of Device or Code names.

• Texts 0 to 532 are used to create SMS event reports

• Texts 601 and 611 are SMS instructions (to control the system remotely by SMS)

• Text 419 is for the internal use of the communicator, never edit it !

5.6. Enabling reporting to phones

Event reports can be enabled as follows:

800 all SMS and call reports disabled

801 all SMS and call reports enabled

802 all reports enabled except reports of setting and

unsetting by users 41 to 50 (i.e. their codes, cards and

key fobs). This allows setting and unsetting done by report

recipients (owners, bosses, etc.) not to be reported.

Factory default setting: 801 all reports enabled

5.7. Remote access

Remote access (by phone or Internet) can be enabled or disabled:

9030 disabled

9031 enabled

Factory default setting: enabled

5.8. Forwarding of incoming SMS messages

This feature enables the automatic forwarding of incoming SMS

messages which contain no valid instructions to the system:

9260 messages are not forwarded, but the communicator sends

them by CLIP protocol to the simulated phone line

9261 messages are forwarded to the first programmed tel.

number in memories M1 to M8 (e.g. if numbers are only

programmed in M5 and M6, then messages will be

forwarded to M5). The tel. number from which the SMS

was received will be shown at the beginning of the

forwarded text.

Factory default setting: messages are forwarded

5.9. SMS instruction confirmation

If the communicator receives a valid SMS instruction, the instruction

sender will be made aware of its successful execution by the reception

of a conformation SMS sent by the communicator. This confirmation

can be disabled as follows:

9270 disabled

9271 enabled

Factory default setting: enabled

5.10. Reaction to incoming calls

The communicator’s reaction to incoming phone calls can be set by:

904 x

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-80Y Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80Y

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info