Bedienungsanleitung Jablotron JA-80Y (Seite 9 von 12) (Englisch)

555058

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

The JA-80Y GSM communicator - 9 - MFJ55304

The telephone numbers M1 and M8 will also receive the GSM

provider’s replay.

• If only uu..u follows the CREDIT instruction (no xx yyy zz) then

periodic balance checking will not be performed, but the balance will

be checked immediately and the uu..u checking instruction will be

memorized, so that in future it will be possible to check the balance

just by sending the instruction code CREDIT.

Example: sending the SMS instruction “code credit

∗

101# 7 50 1”

causes the credit balance to be checked every 7

day (after the SMS

has been sent) and if the balance (starting with the first character in

the message from the GSM provider) is lower than 50 currency units it

will be reported.

Warning:

the use of prepaid cards in the communicator is risky.

Some GSM providers block cards with enough credit but which are not

topped up frequently enough. We strongly

advise the use of tariffed

SIM cards !!!

5.18. Remote programming by the SMS instruction

Instruction PRG can be used to send programming and operating

sequences to the alarm system:

code_PRG_seq,seq,seq...

where:

code is valid access or service code (e.g. 8080 or 1234)

_ space

seq programming sequence usually set via the keypad

Note:

• In the sequence can be used characters 0 to 9, ∗ and #)

• When the valid instruction is received, communicator simulates

entering the keys on the keypad, comma in the SMS is taken as a

pause in the sequence entering

• System must be unset and switched to the service mode

• The number of sequences in one SMS is limited by the maximum size of

the SMS in the GSM network.

Example: by sending SMS 8080 PRG

∗

08080,201,# the exit delay will

be set to 10s

5.19. Registration code for www.GSMLink.cz

If remote access via the Internet is desired, then the system has to be

registered on the web page: www.GSMLink.cz

Each communicator has its own unique registration code, which is

printed on the label attached to the communicator module. This code

can also be sent by SMS to your mobile phone by the keypad entry:

910 xx...x ∗0 where xx...x is the tel. number to send the code to

Notes:

• It takes a certain time to receive the registration code (depends on

the current traffic in the network)

• The registration code has the format: xxxxx-xxxxx-xxxx

5.20. Triggering re-registration to the GSM network

After 923 has been entered, the communicator quits the GSM network and

then re-registers itself. This re-registration does not change any settings in

the communicator. It should be used after GSM network faults or data

collisions and in some networks it also has to be used after a blocked SIM

card has been unblocked by the GSM provider.

It is also possible (if the SIM card can still receive) to trigger GSM network

re-registration by sending the SMS instruction: code GSM (code =

master, user or service code).

5.21. Communicator reset

Entering 98080 returns the communicator to its factory default settings and

texts, erases all telephone numbers and disables reporting. The text will

not be changed.

5.22. Memorizing the SIM card’s PIN code in the communicator

It is recommended to use a SIM card with disabled PIN protection. If it is

impossible to disable the PIN, then it can still be used by entering the

following sequence (it must be entered after the control panel has been

powered up).

920 PIN ∗0

Example: if the SIM card PIN is 1234 enter 9201234∗0

Notes:

 If the communicator does not register to the GSM network within

1 minute of the PIN being entered (this problem is shown by red

LED flashes), then you either entered a wrong PIN or the GSM

signal is too weak. In such a case:

o enter 920∗0 while in service mode (erases the entered PIN)

o disconnect the control panel power (mains and battery)

o take out the SIM card and try it in a mobile phone (it should

o if you know the right PIN code and there is a GSM signal

strong enough, put the SIM card back into the communicator,

turn on the control panel power and then enter the PIN code

(920 PIN ∗0) – the communicator should then register to the

GSM network (its red LED should turn off within a minute)

 The communicator memorizes the PIN and it will use it

automatically whenever it registers to the GSM network.

 If you are replacing the SIM card in the communicator with

another one and the former one used a PIN code, first switch the

control panel to service mode and enter 920∗0 to erase the

former PIN code. The SIM card can then be changed.

Note: The PIN code cannot be changed if the ARC settings are locked

Factory default setting: The PIN code is erased

5.23. GPRS log-in parameters

GPRS data communication (wireless Internet via a GSM network) is

used for remote access via the Internet and also for IP reporting to the

ARC. To use GPRS data it must first be enabled (activated) in the SIM

card (contact your GSM provider for details). Then the GSM network’s

GPRS parameters must be programmed by sending the following SMS

instruction to the communicator.

code_GPRS_ x..x,y..y,z..z

where:

code is a valid (master, user or service) access code (e.g.

8080 or 1234)

_ space

x..x APN (Access Point Name)

, comma

y..y username (do not enter if not required)

z..z password (do not enter if not required)

Notes:

 Most public GSM networks only request an APN (do not enter y..y

and z..z parameters in this case)

 The GPRS parameters can only be programmed if the system is in

service mode and the ARC settings are not locked

Factory default setting: APN = Internet

5.24. ARC phone numbers / IP addresses

Events can be reported to up to 2 ARCs (which can be independent or

ARC2 can work as ARC1’s backup). Each ARC can have its main and

backup phone numbers (or IP addresses) programmed with:

Main: 01 a xx....x ∗0

Backup: 02 a xx....x ∗0

where:

a 1=ARC1, 2=ARC2

xxx...x tel. number (max. 20 digits)

or IP address and port – entry format example:

01 2 ∗8 192 168 001 123 08080 ∗0

where ∗8 (auto-converts to #) signifies an IP address

which must have 12 digits and must be followed by the 5

digits of the port number (no separators)

To erase a tel. number / IP address enter: 01p∗0 or 02p∗0

If numbers / IP addresses are erased there will be no reporting to that

particular ARC

Note: the communicator first tries to send data to the main number /

address, if it is not successful it tries the backup.

Factory default setting: all tel. numbers / IP addresses erased

5.25. Installation (alarm system) ID for ARC use

The installation’s ID number which is sent to an ARC with every report

can be programmed with:

03 a zz..z ∗0

where:

a 1=ARC1, 2=ARC2

Jablotron JA-80Y Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80Y

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info