Bedienungsanleitung Makita UN490D (Seite 10 von 30) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

600703

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Adjusting the cutting angle

WARNING:

• Do not operate the tool with the loose and unstable

cutter unit. Otherwise the cutter unit may change

direction suddenly and cause injury.

CAUTION:

• The cutter unit is fastened only with certain angles

alongside the groove on the unit. Make sure the cutter

unit sits properly. If the angle is not appropriate, the

clutch is cut and the tool does not operate.

• Do not adjust the cutter unit while the pole hedge

trimmer is in an upright position.

• Switch off the tool and remove the battery cartridge,

and lay the pole hedge trimmer flat on the ground to

adjust the cutting angle.

• Always secure the blades with the blade cover

provided before adjusting cutting angle. (Fig. 8)

You can adjust the cutting angle upwards to 45° and

downwards to 90°.

1. Remove the battery and lay the machine on the

ground.

2. To adjust the angle of the cutter unit, hold the handle

on the cutter unit with one hand, and hold the angle

lock as illustrated with the other hand.

3. Pull the angle lock gently, and change the angle of the

cutter unit. After adjusting the angle, return the angle

lock gently. (Fig. 9)

In case the cutter unit is loose, the bolt (the axis of angle

adjustment) needs to be tightened.

4. Set the socket wrench and the hex wrench on the bolt.

5. Adjust the tightness of the cutter unit by turning hex

wrench, and then fasten the bolt by turning the socket

wrench.

NOTE:

• Do not fasten the cutter unit too tight. The angle of the

cutter unit can not be changed if it is too tight.

ASSEMBLY

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before carrying out

any work on the tool. Failure to switch off and remove

the battery cartridge may result in serious personal

injury from accidental start-up.

• Never start the tool unless it is completely

assembled. Operation of the tool in a partially

assembled state may result in serious personal injury

from accidental start-up.

Installing the battery guard (Fig. 10)

Install the battery guard and tighten it with four screws.

Installing the loop handle (Fig. 11)

Securely fit the loop handle onto the shaft pipe with two

screws and clamps.

Make sure that the loop handle assembly is located

between the front grip and the arrow mark.

Attaching shoulder harness (Fig. 12)

Put the shoulder harness on your left shoulder by putting

your head and right arm through it. Keep the tool on your

right side.

After putting the shoulder harness, attach it to the tool by

connecting the buckles provided on both the tool hook

and the harness. Be sure that the buckles click and lock

completely in place.

Adjust the strap to the suitable length for your operation.

(Fig. 13)

The buckle is provided with a means of quick release

which can be accomplished by simply squeezing the

sides and the buckle.

WARNING:

• Be extremely careful to maintain control of the tool

at all times. Do not allow the tool to be deflected

toward you or anyone in the work vicinity. Failure to

keep control of the tool could result in serious injury to

the bystander and the operator.

OPERATION (Fig. 14)

Do not attempt to cut branches thicker than 20 mm

diameter with this trimmer. These should first be cut with

shears down to the hedge trimming level.

CAUTION:

• Do not cut off dead trees or similar hard objects. Failure

to do so may damage the tool.

Horizontal cut (Fig. 15)

When trimming hedges horizontally, follow the steps

below.

1. Pull the switch trigger fully.

2. Apply the blades to the hedge with an angle of 15° to

30°.

3. Trim the hedge with a swinging movement.

Vertical cut (Fig. 16)

When trimming hedges vertically, follow the steps below.

1. Pull the switch trigger fully.

2. Apply the blades to the hedge parallel to each other.

3. Trim the hedge from the bottom upwards with a

swinging movement.

MAINTENANCE

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before attempting to

perform inspection or maintenance on the tool.

Failure to switch off and remove the battery cartridge

may result in serious personal injury from accidental

start-up.

• Before handling or working around blades, wear

protective gloves and put the blade cover onto blades.

During the assembly or adjustment, your fingers may

contact with blades and it may cause serious injury.

• When inspecting or maintaining the equipment, always

put the hedge trimmer down. Assembling or adjusting

the equipment in an upright position may result in

serious injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita UN490D Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info