Bedienungsanleitung Morso 4300 (Seite 15 von 19) (Englisch, Dänisch)

744394

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

DK ENG

2.0 Firing/using the stove

Your stove is constructed with air inlet in 1 place.

Pre-heated, fast-moving combustion air is fed across the glass window and is regulated us-

ing the handle located behind the lower door. The combustion air is let in when the handle

is pushed to the right and shut o when the handle is pushed to the left.

The stove’s rated heat output is 5,0 kW.

Your new Morsø stove is EN-tested for ring with wood, and is suitable for intermittent use.

2.1 Lighting instructions and fuelling intervals

A lot of air is needed when lighting the stove. If you are starting with a cold stove, the door

should be left ajar for the rst few minutes and the combustion air supply opened to maxi-

mum.

To aid lighting your stove, a starter unit has been tted in the bottom right corner of the

stove door. To keep the door ajar when starting up, lift the small stainless steel handle while

closing the door. When you can see (after 5-10 min.) that the chimney draft is established,

close the door completely by opening it a little rst. The small stainless steel handle will

drop under its own weight and move out of the startup position. The stove door then closes

by itself.

In order to build up an insulating layer of ash in the bottom of the stove, you should burn 1-1.5

kg of dry kindling when you light the stove the rst time.

Always keep approx. 1 cm ash in the bottom of the combustion chamber.

NB!

Wood is a material that contains a great deal of gas (approx. 75%). The gases are released

when the wood is lit and heated. For this reason, it is important that these gases are ig-

nited quickly after stoking. If the wood just lies smouldering, especially after re-stoking,

a lot of smoke is created which, in the worst case, may cause an explosive ignition of the

gases, resulting in damage to the stove.

In order to ignite the gases that are released from the wood, and to keep clear, lasting

ames during the combustion process, it is important to let in the required quantity of

oxygen (air supply) at all times. The setting of the air supply, the method of ignition and

the lighting intervals depend on the draught in the chimney, the wind and weather, the

amount of heat required, the fuel, etc. This means that it may take some time before

you get to know the correct functioning of the stove under any given circumstances.

Although you can re your Morsø stove with almost all kinds of wood, you should

not re with wet wood, or unseasoned wood. Wood ought to be stored under a roof

for at least 1 year, and preferably 2 years, with free access to wind. Wood should be

chopped as soon as possible after felling if it is to dry quickly. The wood can be used

once the moisture is less than 20%. During the test, all stoves are tested with wood

with a moisture content of (16 ± 4)%.

Never use driftwood as it usually has a high salt content, which damages both

the stove and the chimney. Impregnated and painted wood and chipboard emit

poisonous smoke and fumes so they should not be used as fuel either

Please note that liquid fuel may not be used in the stove.

Pieces of wood with a diameter exceeding 10 cm should always be chopped. The pieces

of wood should be short enough to be able to lie at over the layers of embers, with air

at both ends. The maximum length of fuel in the stove is 25 cm. The maximum quantity

of fuel is approx. 2 kg/hour (max. 2 pieces of wood each time you re-stoke).

The rst few times you light the stove, the re should be moderate so that the heat-

resistant paint can harden before ring more vigorously. During the hardening phase,

the paint may develop obnoxious smoke and smell the rst time it is lit, which is very

normal. Make sure that the room is well ventilated during this period.

When heating up or cooling down, the material is exposed to major temperature

dierences that may cause the stove to give o creaking sounds.

1. The layer of embers is formed quickly when lit with 2-4

kindling tablets or similar together with approx. 1-1.5 kg of

dry kindling. Place the kindling sachets evenly under the top

layer of kindling.

2. Open the air supply as much as possible. This is done

using the handle above the door.

3. After the paper/solid alcohol tablets have caught re,

leave the re door ajar so that the chimney draws well.

Lift the small stainless steel handle in the bottom right

corner of the door while the door is closing. This keeps

the door ajar during the startup stage.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Morso 4300 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Morso 4300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info