Bedienungsanleitung Morso 4300 (Seite 17 von 19) (Englisch, Dänisch)

744394

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

DK ENG

3.0 Routine stove maintenance

3.1 External maintenance

The cast surface of the stove is painted with heat-resistant Senotherm paint. It is best main-

tained by simply vacuuming it with a soft brush attachment or wiping it down with a dry,

dust-free cloth.

If the stove is used too vigorously, the painted surface may assume a greyish tinge over time,

but the stove can easily be freshened up with Morsø spray paint, which is available from your

local retailer.

Morsø stoves are painted using a Morsø Original Black (previously called Morsø dark grey)

or Morsø grey. The paint can be bought in a spray or a can.

3.2 Internal maintenance

Glass window

If the stove is used correctly, very little or no soot will be deposited on the ceramic glass

window. If soot does form on the glass as the stove is being lit, it will burn away once normal

combustion begins in the stove. If the glass window becomes thoroughly covered in soot

due to incorrect operation, the soot can be easily removed using Morsø Glass Cleaner. The

glass must be cold when you clean it. Avoid stoking the stove with pieces of wood that are

so long that they press against the glass window when the door is closed.

Only use Morsø Glass Cleaner.

Ceramic glass replacement

Ceramic glass cannot be recycled because it has a higher melting point that ordinary glass.

If ceramic glass is mixed with ordinary glass, the raw material is spoiled, and the reclaiming

process may be halted. Take care that the ovenproof glass does not end up among ordinary

recycled waste. That will be a great benet to the environment.

Note: Should be handed in to a recycling station as ceramic glass.

Internal cast-iron grate and/or wearing parts

The baes and other components that come in direct contact with the re and glowing fuel

are all wearing parts. As a result, they will be particularly susceptible to burn-through. When

used correctly, these parts will last for many years, but overly vigorous use will naturally ac-

celerate the burn-through. Such parts are all easily replaced. If the baes are damaged and

are not replaced in time, the top plate will be exposed to such high temperatures that it may

be damaged as well.

Reasons for sooty glass window:

- The fuel is too wet.

- The pieces of fuel are to big/uncut wood.

- The combustion temperature is too low.

Reasons for overly rapid wear of internal parts

- Stove red too vigorously

- Use of very dry wood (wood from old furniture).

- Too much soot on top of the baes (please see the section on Cleaning).

- Too much ash in the ash pan (please see the section on Ash).

Please note that no unauthorised alterations of the design may be undertaken, and that

any parts that are replaced must be replaced with original Morsø parts.

Gaskets

The gaskets in the doors will wear out over time and should be replaced as required in order

to prevent runaway combustion. Use the original Morsø gasket kit.

Note: Normal wearing parts are not covered by Morsø’s extended warranty.

A selection of maintenance products (spare parts, glass cleaner, paint, gasket kit, etc.) is avail-

able from your Morsø dealer.

3.3 Cleaning the stove

A layer of ash and soot will form as a result of the draught in the chimney and after sweep-

ing, particularly on the top of the upper bae. This ash will have an insulating eect, which

may speed up the burn-through of the baes.

During normal cleaning, the baes can be removed from the stove. Once the baes have

been taken out, you can access the ue chamber above the baes and clean it.

Clean the baes before reassembling them, and make sure that they are correctly assem-

bled.

Nowadays, the chimney sweep must remove the soot in the stove, in addition to sweeping

the chimney and cleaning the ue pipe. The number of annual sweepings/cleanings of the

stove should be determined in consultation with your chimney sweep.

Ash

As noted above, there should be a layer of approx. 1 cm insulating ash in the bottom of the

combustion chamber in order to achieve a high combustion temperature. If the layer of ash

is too thick, it can be brushed down into the ash pan.

Empty the ash pan before it gets completely full so that the ash does not insulate around

the grate, and thereby speed up the burn-through.

In most cases, the ash will need to be taken away by the waste disposal company. Because

embers may be concealed in the ash pan for several days, it may be necessary to store the

ash in a container made of non-ammable material before pouring it into a rubbish bag.

Ash from a wood-burning stove will not be of any benet to your garden as fertiliser. If you

have burned colour brochures, or painted or treated wood, etc., in the stove, the resulting

ash must not be poured onto soil as it may contain heavy metals.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Morso 4300 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Morso 4300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info