Bedienungsanleitung Multiplex COCKPIT SX (Seite 79 von 84) (Englisch)

561578

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Operating Instructions

Page 77

ENGLIS

Moving to the START1 menu:

4 to MENU, r (SETUP appears),

3 to TIMER, r (START1 appears),

Start time for Timer 1 in minutes : seconds

The first number of the current start time flashes. Use

the 3-D digi-adjustor to set the “tens” of minutes. A brief

press r on the 3-D digi-adjustor takes you on to the

next digit.

Once you have set the “single second digits”, a brief

press r on the 3-D digi-adjustor concludes the process.

Important: the current time is stored.

The current time of Timer 1 is stored when you switch

the transmitter off. If you want the set time to start

again next time you switch on, you must first reset

Timer 1 in the INFO 2 or INFO 3 menu (long press

ª on the 3-D digi-adjustor).

If the assigned switch is at the ON position when you

switch the transmitter on again, Timer 1 immediately

resumes counting.

19.2. Timer 2

Timer 2 is ideal for recording the overall flight time. It

always starts at 00:00. The transmitter control selected

as the timer switch can start Timer 2, but it cannot stop

it again.

Timer 2 runs to a maximum of 99 minutes, 59 seconds.

Timer 2 can be started, for example, when the throttle

is advanced for the first time, when the tow-release is

operated, or when you operate the PH switch to switch

from the launch setting to normal flight.

19.2.1. Assigning a timer switch

Menu: (

TIMER) T2 SW

Example 1: starting Timer 2 using the THROTTLE

In this case the switch is assigned using the method

described in section Î 19.1.1.

Example 2: starting Timer 2 using the PH switch

Requirements:

The model must be programmed with flight phases.

Flight phase 1 is the “launch setting”, and flight phase 2

is “normal flight”.

The following example shows how to start Timer 2 (with

the stated requirements fulfilled), when you switch for

the first time from the “launch setting” to “normal flight”.

Moving to the T2 SW menu:

4 to MENU, r (SETUP appears),

3 to TIMER, r (START1 appears),

3 to T2 SW r

No switch Switch 4

Move the PH switch quickly to and fro until code num-

ber 4 appears. The hyphen following the colon indi-

cates the switch position which triggers the timer.

Switch 4 Marker Switch position

Now move the PH switch to the position which is re-

quired to trigger the timer (in our illustration Phase 2).

A brief press r on the 3-D digi-adjustor concludes the

process. The flashing ceases, and the setting is stored.

19.2.2. Stopping Timer 2, or resetting it to 00:00

Timer 2 can only be stopped or reset if it is visible in

the bottom line of the screen. There are two methods of

doing this:

In the INFO 3 display:

Pressing the 3-D digi-adjustor at this display affects

both timers.

INFO 3 display: both timers

In the INFO 4 display:

Pressing the 3-D digi-adjustor at this display only af-

fects Timer 2.

INFO 4 display: Timer 2 only

Stop timer: r brief press on 3-D digi-adjustor

Setting timer to 00:00: ª long press on 3D digi-adjustor

Phase 3

Phase 2

Phase 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex COCKPIT SX Seite 79

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex COCKPIT SX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info