Bedienungsanleitung Multiplex ROYALevo7 (Seite 6 von 77) (Englisch)

30268

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

ROYAL evo 7 - Instructions

Page 5

ENGLIS

x Do not coil, shorten or extend the receiver aerial.

Never deploy the aerial parallel to any electrically

conducting part, e.g. metal pushrod, or inside a fuse-

lage with a shielding effect (made of or reinforced

with carbon fibre or metallic paint). Do not attach the

aerial to any electrically conductive model compo-

nent. We recommend the use of whip aerials in large-

scale model aircraft.

x Take care to provide a receiver power supply of ade-

quate capacity. For servos up to about 40 Ncm you

can use the following formula for estimating the re-

quired battery capacity:

mAhservosofNomAhCapacity 200.][ ut

I t i s a l w a y s b e t t e r t o s e l e c t t h e n e x t l a r g e r s i z e o f b a t -

tery, unless weight or space considerations prevent it.

x Make sure that moving parts made of conductive ma-

terials (e.g. metal linkage components or pushrods)

cannot contact each other, as they may generate

electrical “noise” which interferes with the receiver.

x Interference from static charges and powerful electri-

cal or electro-magnetic fields must be avoided by

suitable suppression measures (e.g. fit suppressor ca-

pacitors to electric motors, suppress petrol engines

with shielded sparkplug connectors, ignition leads

and ignition units), and keep these parts well away

from the RC system, receiver aerial, wiring and batter-

ies.

x Maintain an adequate distance between high-current

cables (e.g. electric power system) and the RC system.

In particular, keep the cables between brushless elec-

tric motors and their controllers as short as possible

(max. 10 - 15 cm).

x Always program a new model at home, in peace, and

check each working system very carefully. Make sure

you are familiar with the programming methods and

operation of the transmitter before you take the

model out to the field and fly it.

Check the model at regular intervals

x Freedom of movement and lack of slop in control sur-

faces and mechanical linkages

x Rigidity and good condition of pushrods, linkage

components, hinges etc.

x Visual check for fractures, cracks, signs of stress etc.

on the model itself and its components, such as the

receiving system and power system

x Perfect condition and contact security of cables and

electrical connections

x State of the power supply and it’s wiring, including

switch harness, and external check of the condition of

battery cells. Regular maintenance of batteries and

voltage / capacity checks, using a charger and charg-

ing method designed for the battery type in use.

Pre-flight checks:

x Check the transmitter, receiver and drive / flight bat-

teries carefully, and check their state of charge be-

tween flights. This requires the use of a charger and

charging method which suits the batteries in your

model, and regular battery maintenance (cell balanc-

ing), plus checking the voltage curve and capacity.

x At the flying site always check first with the other

modellers that your frequency is free; register with

the site administrator if present and check the

method of frequency control in use. Do not switch ON

until you have done this. If you neglect this, you run

the risk of a frequency clash and crashed models!

x Carry out a range check with the transmitter aerial

collapsed. (Î 3.2.)

x Ensure that you have selected the appropriate model

memory.

x Check that all primary and auxiliary functions are op-

erating correctly.

! If you find or suspect a fault, do not launch the

model. Locate the defect, eliminate it, and then

repeat the full check.

When operating the model:

x If you are a beginner to RC models, you really must

recruit the help of an experienced model pilot. A

Trainer system is excellent for initial practice.

x Models may only be flown at suitable approved sites.

x Never fly your model above or towards spectators.

x Do not carry out high-risk flight manoeuvres.

x Don’t over-estimate your own piloting skill or ability.

x If you detect any sign of a problem or interference,

land the model or cease operations immediately.

x Be aware of static charge problems!

In extremely cold air (mountainous terrain, high slope

bowls, proximity to storm fronts) static charges build

up in the transmitter and/or pilot. When a discharge

(spark) takes place the pilot may be injured, and the

transmitter might be damaged or suffer interference.

Counter-measures:

Cease operations as quickly as possible. Walk down-

hill a little way; this is often enough to reach a less ex-

posed location.

x Keep at least 2 m away from mobile telephones!

When using your RC equipment keep at least 2 m

away from any mobile telephone, as the high trans-

mitted power of the mobile may cause radio interfer-

ence to the transmitter or RF module.

In general terms we recommend that you switch off

mobile telephones and any other piece of equipment

which could cause the pilot to lose concentration

when flying.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo7 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info