Bedienungsanleitung Multiplex ROYALevo7 (Seite 7 von 77) (Englisch)

30268

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

ROYAL evo 7

Page 6

Static discharge protection of electronic sub-

assemblies

The sub-assemblies of a radio control sys-

tem transmitter (main circuit board, RF

module, Channel-Check, scanner) are fitted

with components which are electro-

statically sensitive. They can be destroyed,

or their useful life shortened, if an electro-static dis-

charge takes place when the sub-assembly is touched.

Be sure to take the following protective measures when

handling electro-statically sensitive sub-assemblies:

x “Earth” yourself before touching or working on such

assemblies by making electrical contact with your en-

vironment (e.g. touch an earthed radiator).

Open the base unit (if necessary) and touch a large

area of it, to create potential balance relative to the

base unit.

x Do not take the sub-assembly out of its conductive,

statically shielded bag until you have earthed your-

self. Avoid touching the electronic components or

soldered joints directly. Hold the sub-assembly only

by the edges of the circuit board.

x If you have to store a sub-assembly outside the base

unit, keep it in the protective conductive bag in which

the module was supplied. Never allow the module to

contact a conventional (non-protective) foam, styro-

foam or other plastic material directly.

3.2. Range checking

Range checking is a method of testing the RC system

which gives extremely reliable information about the

operating condition of your radio control system.

We have concocted a range-check recipe which will al-

ways leave you on the safe side. It is based on our own

experience and measurements.

1. Move the aerial to an upright,

angled position and collapse

the segments completely

(push them together) (Î

9.5.2.).

2. Set up the model with the tip

of the receiver aerial about

1m above the ground.

3. Ensure that there are no large

metallic objects (e.g. cars,

wire fences etc.) in the vicin-

ity of the model.

4. Do not carry out the check if

there is any other transmitter

switched on - even on a dif-

ferent channel.

5. The range check will not

work properly in mountainous regions.

6. Switch on the transmitter and receiver. At a range

of about 80m between transmitter and receiver

check that the control surfaces respond accurately

to the stick movements, and do not carry out any

uncontrolled movements. Close to the range limit

the servo output arms may move from their nomi-

nal position by up to the width of the arm (servo jit-

ter).

7. Secure the model and repeat the check with the

motor running (varying the throttle setting from

idle to full-speed).

The stated range of 80m is only a general guideline. Ac-

tual range varies widely according to environmental

conditions. For example, in mountainous terrain or in

the vicinity of powerful radio transmitters, radar stations

or similar installations, effective range may only be half

that stated.

If radio range is restricted, what can you do to locate

the cause of the problem?

1. Change the position of the receiver aerial.

Metal or carbon fibre reinforced parts close by will

adversely affect reception conditions.

The effect of electric power systems and ignition

systems also alters if you change the position of the

aerial.

2. Disconnect the servos from the receiver one by one,

repeating the range check each time.

Over-long cables without suppressor filters have an

adverse effect on reception conditions. Servos also

deteriorate with age, and generate greater interfer-

ence than when new (brush sparking, motor sup-

pressor capacitors vibrated loose, general wear etc).

If you cannot effect an improvement by simple

means, try removing the complete system and op-

erating it outside the model. This allows you to

check whether the fault is in the system, or in the

installation in the model.

4. Liability / compensation

As manufacturers, we at MULTIPLEX Modellsport GmbH

& Co. KG are not in a position to ensure that you ob-

serve the operating instructions, the conditions and

methods of installing, using, operating and maintaining

the radio control system and its components. For this

r e a s on M U L TI P LE X Mo d e l ls p o r t G m bH & C o . K G de n y a ll

liability for loss, damages or costs which are incurred as

a result of the incorrect use and operation of the

equipment, or are connected with such use in any way.

Unless otherwise prescribed by binding law, the obliga-

tion of MULTIPLEX Modellsport GmbH & Co. KG to pay

compensation, regardless of the legal argument em-

ployed, is limited to the invoice value of that quantity of

products manufactured by MULTIPLEX Modellsport

GmbH & Co. KG which were immediately and directly

involved in the event which caused the damage. This

does not apply if MULTIPLEX Modellsport GmbH & Co.

KG is deemed to be subject to unlimited liability accord-

ing to binding legal regulation on account of deliberate

or gross negligence.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo7 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info