Bedienungsanleitung Multiplex ROYALevo9 (Seite 53 von 58) (Englisch)

30282

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Instructions

Seite 53

ENGLISH

x If you wish to overwrite the existing model data,

press the REV/CLR button.

When the copy process is finished, the software calls up

the previously active model again.

18.3. Sub-menu „Erase“

When you have selected the memory you wish to erase,

press the 3-D digi-adjustor or the ENTER button. The

screen displays the security query “Erase selected

model?”.

x If you do not want to erase the data:

Press ENTER or the 3-D digi-adjustor.

x If you do want to erase the data:

Confirm by pressing the REV/CLR button.

You cannot erase model data if you have selected the

active model memory, i.e. the one marked with the

letter “x”.

18.4. Sub-menu „Flight phases“

I affects active model momory

4 phases are possible

Phases are switched “smoothly”

(over approx. 1 sec)

Phase name can be selected from 13 pre-sets

Phases can be released and blocked

(alarm sound if you select a blocked phase)

Phases can be copied

You can adjust the characteristics of the transmitter

control to suit the requirements of the model for each

flight phase separately, e.g. reduced control travels for

SPEED FLYING, lowered flaps for LANDING, greater col-

lective pitch travel for AUTO-ROTATION. Where settings

are present which can be altered separately for each

flight phase, the code number of the flight phase ap-

pears in the transmitter control menus (Î Fehler! Ver-

weisquelle konnte nicht gefunden werden.).

Basic requirement: if you wish to work with flight

phases, you must first assign at least one phase select

switch (main phase or phases 1-3) in the menu L, AS-

SIGNMENT, SWITCHES. If no switch is assigned, the

transmitter remains permanently in Phase 1.

A typical Flight Phase menu might look like this:

This display tells us the following:

1. Flight phases 2 and 3 are blocked

(name crossed through)

2. Flight phase 1 (main phase) is active

(x after the name)

3. Main phase switch is switch J on the right-hand side

4. No switch is currently assigned to phase 4

(--- after phase 4)

18.4.1. Selecting flight phase names

The following names are available:

NORMAL, START1, START2, THERMAL1, THERMAL2,

SPEED1, SPEED2, CRUISE, LANDING, AUTOROT, HOVER,

3D, ACRO

The phase names are only intended as a reminder for

the operator. The significant factor in the characteristics

of the flight phase is always the number of that phase.

You can select a suitable name after activating the

name input field.

18.4.2. Block / release flight phase

Use the REV/CLR button to release or block the flight

phases. First select the flight phase, then activate the

name, and finally switch between “free” and “blocked

”

using the REV/CLR button. Selecting a different name

using the 3-D digi-adjustor also releases a blocked flight

phase.

The active flight phase (x) cannot be blocked.

If you accidentally select a blocked flight phase

with the phase select switch, you will hear a

continuous warning tone.

18.4.3. Copying the active flight phase

The active flight phase is marked by an “x” after the

name. You can copy the values for this phase into any of

the three other phases. This is the procedure:

1. Select the active phase (x)

2. Press the 3-D digi-adjustor (or ENTER) twice:

the “x” is activated

3. Select the destination phase for the copy: a “c” ap-

pears in the cursor.

4. Confirm with the 3-D digi-adjustor or ENTER

18.5. Sub-menu „Properties“

I affects active model memory

Displays model template used to create this model

This menu displays certain characteristics of the active

model. These characteristics can also be changed, with

the exception of the used template.

Example:

new with software 1.16:

Thr.curve ON/OFF, heli

copters only (Î 14.2.11)

Template indicates the model template you invoked

when you created this model. You cannot change this

setting.

In this example Mode indicates that the left stick con-

trols rudder and elevator. You can change this setting if

you wish.

Assignment indicates which of the available assign-

ment lists for transmitter controls and switches is in use

for this model. You can change this setting if you wish.

The name of the model can be entered at this point,

with a maximum of 16 characters. If you create a new

model, the name of the template you used is automati-

cally entered here.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo9 Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo9

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info