Bedienungsanleitung Multiplex ROYALevo9 (Seite 55 von 58) (Englisch)

30282

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Instructions

Seite 55

ENGLISH

19.3. Other accessories/spar parts

19.3.1. Overview

Article Order No.

Transmitter carrying bag

76 3322

Transmitter carrying case 76 3323

Scanner 35 MHz

36 MHz

40/41 MHz

72 MHz

4 5170

4 5173

4 5171

4 5172

Transmitter tray

8 5305

Space-Box ROYALevo BASIC 8 5658

Space-Box weather protection

8 5655

Transmitter carrying belt

8 5646

Kreuzgurt

8 5640

Gurtpolster

8 5641

Switch 2-position

Stick top button/switch (Î 7.4.10.)

7 5303

19.4. Using MULTInaut IV

Models equipped with the MULTInaut IV receiver unit

can be operated with the ROYALevo.

The buttons of the ROYALevo are used to control the

MULTInaut functions. No additional switches are re-

quired. All you need are the receiver units in the model.

4 buttons are assigned to each MULTInaut channel and

control the connect lamps, servos, etc.

The effect of a key-press depends from the selected

operating mode. The following possibilities exist:

a. Loads at clamp+/-1 to +/-4

The drawing shows how to connect the loads

Drawing for Servo 5 = M.naut 1

switch loads (e.g. lamps, horns, ...)

Each key-press changes (toggles) the status of the

load. (OFF Æ ON resp. ON ÆOFF)

b. Servos at the connectors 1 to 4 (no jumpers)

If no jumpers are set on 2 resp. 4, each key-press

moves the servo from one position to the other.

(right Æ left resp. left Æ right)

c. Servos connected to 1 /3

with jumpers onconnector 2/4

The keys 1 and 2 move the servo at connector 1,

the keys ¾ the servo at connector 3.

As long as the key is pressed the servo moves into

one direction until it reaches its end-point. Releas-

ing the key stopps the servo.

The full travel is split in 32 steps and takes approx.

4 sec.. A short hit on the key initiates a step of

approx. 3°.

This is how to activate MULTInaut:

1. Assign M.naut 1 or 2 to the receiver output where

the MULTInaut module in the model is connected

to.

2. Seeing one of the 4 tatus display, press ENTER

longer than 3 sec. to activate the keys groups for

MULTInaut. The display shows:

”MULTINAUT keyboard active”

3, Press ENTER for more than 3 sec. again to quit the

MULTInaut keyboard mode.

19.5. Diagnosis lead

You can connect the transmitter to the receiver directly

using a diagnosis lead, in which case the transmitter

does not generate an RF signal. This can be very useful

for making adjustments, checking travels etc.

This is the procedure:

1. Connect the appropriate diagnosis lead to the

multi-function socket on the back of the transmit-

ter, and to the model’s receiving system

2. First switch the transmitter on (RF remains off)

3. Switch the receiving system on

Different diagnosis leads must be used according to the

receiving system in the model:

Diagnosis lead

for MULTIPLEX switch leads with charge socket # 8 5105

for the „EinStein“ # 8 5162

Keys group for

M.naut 1

Keys group for

M.naut 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo9 Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo9

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info