Bedienungsanleitung Multiplex ROYALevo9 (Seite 54 von 58) (Englisch)

30282

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

ROYAL evo

Seite 54

18.6. Sub-menu „New model“

When you open this sub-menu the following display

appears:

The transmitter tells you which memory number will

be used: it is always the first vacant memory. You can-

not change the memory number.

The template determines which basic settings are ac-

cepted into the memory (Î 12.4.). You can change this

setting if you wish.

Servo conf. (Servo configuration) defines the assign-

ment of the servos and the signal format. The following

combinations are possible:

Servo conf..

Servo

assignment

Signal format

MPX-MPX

MPX MPX

MPX-UNI

MPX UNI

Futaba

Futaba UNI

JR UNI

The brand-specific assignment sequence (order of ser-

vos at the receiver output) is prepared in four servo

configurations. For MULTIPLEX e.g.: Throttle is on servo

4 and Rudder on servo 3. If the model was operated

with a radio of a different brand before, using the corre-

sponding configuration eases the assignment proce-

dure. In the menu K, Assignment the preset sequence

can be modified to your liking.

Mode defines the assignment of the sticks. In our ex-

ample the left-hand stick controls rudder and elevator.

You can change this setting if you wish.

Assignment defines which of the possible assignment

lists for transmitter controls and switches is to be used

with this model. You can change this setting if you wish.

Select OK to conclude the process, and the new model

is created.

Note:

If there are no vacant memories available, the screen

displays the number -1 and the note “No memory free!”

In this case press ENTER and then “EXIT” the menu.

19. Accessories

19.1. Scanner (with HFM-S RF module)

A scanner module can expand the Synthesizer RF mod-

ule HFM-S of the ROYALevo. The scanner can do two

„jobs“:

19.1.1. Scan the all frequencies/channels in

the band

All channels in the band will be measured sequentially.

Detected signals will show up in the display as bars. The

height of the bar corresponds to the strength of the

signal.

19.1.2. Channel-Check at power-ON

The channel selected for the synthesizer is checked

every time you switch your transmitter ON. If the chan-

nel is occupied already the synthesizer does not start

operation (no RF output) and in the display you will see

a warning. If no signal is detected on your channel,

normal operation starts.

19.1.3. Installation of the scanner module

The user can install the scanner. No tools or adjustments

are required.

Available frequencies/bands: see 19.3. Acessories

Detailed instructions are attached to the scanner mod-

ule.

19.2. Channel-Check

(with the RF module HFM-4)

A Channel-Check module can be installed in the RF

module HFM-4. This module needs a receiver crystal

with the same frequency/channel, which will be used

for the model.

Every time you switch your transmitter on, the module

checks if the channel is occupied or not.

The Channel-Check module for the ROYALevo

is identical with the module, used in the trans-

mitters PiCO line, COCKPIT MM and in the RF

module HFM3.

Available frequencies/bands: see MULTIPLEX

main catalogue

19.2.1. Installation of the Channel-

Check module

Switch OFF and open the transmitter

remove the RF module

Install the desired receiver crystal in the Channel-Check

module

plug Channel-Check module onto the RF module

reinstall the unit in the transmitter

19.2.2. Operating Channel-Check

Expand the aerial fully

Switch the transmitter on

LED glows permanently: Channel occupied

LED flashes: Channel free

(without guarantee)

If the channel is occupied the following message ap-

pears in the display:

Channel Used!

Channel-Check

module

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo9 Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo9

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info