Bedienungsanleitung NAD C 326 BEE (Seite 10 von 16) (Englisch)

493507

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

USING THE SR 8 REMOTE CONTROL

The SR 8 remote control handset handles the key functions of the C 326BEE as well as other NAD

Stereo Receivers, Integrated Ampliers and Preampliers. It has additional controls to remotely operate

NAD CD Players, AM/FM Tuners and dedicated AM/FM/DAB Tuners. It will operate up to a distance of

23ft (7m). Alkaline batteries are recommended for maximum operating life. Two AA batteries should

be tted in the battery compartment at the rear of the Remote Control handset. When replacing

batteries, check that they have been put in the right way round, as indicated on the base of the battery

compartment.

When a command from the remote control is received, the Standby LED indicator will blink. Note that

the indicator may also blink when receiving commands not necessarily for the C 326BEE but for other

components in the system. Please refer to previous sections of the manual for a full description of

individual functions.

NOTE

The remote control handset supplied with the C 326BEE is of a universal NAD type, designed to

operate several NAD models. Some buttons are applicable only to specic NAD models. Contact

your dealer or NAD audio specialist for assistance.

1 POWER ON & OFF: The SR 8 remote has a separate ON and OFF button. Press the ON button

to switch the unit from Standby to operating mode. Press the OFF button to switch the unit to

Standby mode.

2 DEVICE SELECTOR: A Device Selector button determines only what component the SR 8 will

command; it does not perform any function on the C 326BEE. Press desired Device Selector button

for the applicable buttons to be directed to a “page” of commands relevant to the selected device.

Upon selecting a Device, you can now press the corresponding SR 8 control buttons applicable for

the selected Device.

3 INPUT SELECTORS: Refer to the corresponding labels printed in the remote control faceplate

and their respective assigned buttons to make use of these functions. Set the DEVICE SELECTOR

to “AMP” in order to gain access to these buttons. The input selector buttons perform the same

functions as the buttons labeled the same on the front panel.

4 NUMERIC KEYS: The numeric keys allow for direct input of tracks for CD players, and direct

channel/preset access for tuners and receivers.

5 SLEEP: Switch o specic NAD Receiver or Tuner models after a preset number of minutes.

6 MUTE: Press the [MUTE] button to temporarily switch OFF the sound to the speakers and

headphones. MUTE mode is indicated by the Standby LED indicator ashing for NAD Integrated

Ampliers or “Mute” shown in the VFD of NAD Receivers. Mute does not aect recordings made

using the TAPE output but will aect the signal going to the PRE OUT output. Press MUTE again to

restore sound.

7 DIM (for use with NAD Stereo Receiver, Tuner and CD Player): Reduce, turn o or restore VFD

brightness. Depending on the NAD model, the brightness of the front panel display will vary when

you toggle this button.

IDENTIFICATION OF CONTROLS

SR 8 REMOTE CONTROL

3, 4

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 326 BEE Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 326 BEE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info