Bedienungsanleitung NAD C 326 BEE (Seite 12 von 16) (Englisch)

493507

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

USING THE SR 8 REMOTE CONTROL LIBRARY

The SR 8 can store a dierent library of default NAD codes for each

of its DEVICE SELECTOR “pages.” If the original default library does not

control your NAD CD player, DVD player or other components, follow the

procedure below to change the library code. Refer as well to the table

below for a list of applicable NAD Library Codes with their corresponding

NAD models.

LOAD ANOTHER LIBRARY CODE

Example: Load NAD DVD Player T 517 library codes to SR 8’s “CD” device.

1 Press and hold [CD] in the DEVICE SELECTOR section of SR 8.

2 While holding down the device button (CD), press “2” and “2” using SR

8’s numeric buttons. “22” is the corresponding library code for T 517.

3 Press [ENTER] while still holding down the device button (CD). The

CD device selector will ash once to indicate that the library input is

successful. Both the device selector button (CD) and [ENTER] can now

be released.

RESET THE SR 8 TO ITS DEFAULT SETTINGS

The SR 8 can be restored to its factory settings, including default libraries,

by the following procedures

1 Press and hold [ON] and [DELETE/CLEAR] buttons for about 10 seconds

until the AMP device button lights up.

2 Within two seconds of the AMP device button lighting up, release both

buttons. If the reset mode is successful, the [CD] device button will ash

twice.

TABLE OF LIBRARY CODES APPLICABLE TO SR 8 REMOTE

CONTROL

LIBRARY

CODE

NAD PRODUCT DESCRIPTION

10 Default library for “AMP” page

11 Zone 2

20 Default library for “CD” page; C 515BEE, C 545BEE, C565BEE

21 T 535, T 585, M55, DVD section of L 54, VISO TWO, VISO FIVE

22 T 513, T 514, T 515, T 517

23 T 587

31 IPD 2

Default library for “TUN” page; Tuner section of C 725BEE, T 175,

T737, T 747, T 755, T 765, T775, T 785

41 C 422, C 425

42 C 445

NOTE

The SR 8 may not necessarily contain all the control buttons applicable

for the above-mentioned NAD products. Use the prescribed remote

control of the specic NAD product for a full compliment of the

applicable remote control buttons.

ALTERNATE IR CHANNEL

The C 326BEE has the capability to operate via Alternate IR channel. This

is practically useful if you have two NAD products that can be operated by

similar remote control commands. With alternate IR Channel, two dierent

NAD products can be controlled independently in the same zone by

setting each one to a dierent IR channel.

IR CHANNEL ASSIGNMENT

The C 326BEE and the SR 8 remote control must be set to the same

channel.

To change the IR Channel on the C 326BEE

Press and hold [MP] button and then press Standby button. Observe the

number of times the Standby LED ashes.

• IR Channel 1 - Standby LED ashes once.

• IR Channel 2 - Standby LED ashes twice.

To change the IR Channel on the SR 8 remote control

• Include a channel number before the library code. For SR 8, library code

“10” is the default library table for “AMP” device. To select this “AMP”

library table for “IR Channel 0”, retain the library code “10”.

• If you want to load the “AMP” library table on “IR Channel 1”, prex the

library code with “1” to indicate association with “IR Channel 1”. Load

then the “AMP” library table using the code “110”.

SAMPLE SETUP OF TWO NAD PRODUCTS ON THE SAME ZONE

C 326BEE and T 787 are both defaulted to IR Channel 0. If [OFF] button is

pressed on the SR 8 remote control (or HTR 8 remote control for the T 787),

both products will go to standby mode. Press [ON] and both products will

power up from standby mode.

To prevent both products from simultaneously going in and out of standby

mode along with other common commands, set each one to a dierent

IR channel. In this setup, we will keep T 787 and HTR 8 remote control

defaulted to “IR Channel 0”. As for C 326BEE, we will assign it to “IR Channel

1”; the same applies to SR 8.

Set C 326BEE and SR 8 to “IR Channel 1” via the following procedure.

C 326BEE

• Press and hold [MP] button and then toggle STANDBY button until the

Standby LED ashes twice - C 326BEE is set to “IR Channel 1”.

SR 8

Begin by ensuring that the C 326BEE is powered-up (“on”, not merely in

standby).

• Press and hold [AMP] in the DEVICE SELECTOR section of the SR 8.

• While holding down the device button [AMP], press “1”, “1” and “0” using

SR 8’s numeric buttons.

• Press [ENTER] while still holding down the device button [AMP]. The

AMP device selector will ash once to indicate that the library input is

successful.

With both C 326BEE and SR 8 set to “IR Channel 1”, the C 326BEE can now

be remotely controlled independent of the T 787.

NOTE

Performing a Factory Reset for SR 8 will result to a return to the factory

default “IR Channel 0” setting.

IDENTIFICATION OF CONTROLS

SR 8 REMOTE CONTROL

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 326 BEE Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 326 BEE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info