Bedienungsanleitung Naim NaimUniti 2 (Seite 4 von 25) (Englisch)

707486

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

NaimUniti 2 Installation and Connection

2.2 Mains Power Connection

Connect NaimUniti 2 to a mains power socket using either

the mains cable supplied or a Naim Power-Line.

2.3 FM/DAB Aerial Connection

In order to enable high quality FM and DAB radio,

NaimUniti 2 requires a strong, interference-free radio signal.

Its rear panel FM/DAB Aerial socket must be connected,

via 75 Ohm low-loss coaxial cable, to a suitable aerial. The

aerial should be mounted clear of large obstructions and

as high as possible; ideally on a roof.

Note: Your local retailer should be able to offer advice on

a suitable aerial and aerial installer.

2.4 Audio Signal Connections

2.4.1 Audio Signal Inputs

NaimUniti 2 provides five stereo analogue inputs and five

S/PDIF digital inputs including one combined analogue/

digital input socket. Connection to the inputs is made via

a variety of socket types. The following table lists the inputs

and their socket types:

Input Type Socket

an. 1 Analogue RCA phonos

an. 2 Analogue RCA phonos

an. 3 Analogue RCA phonos

phono Analogue 240° 5 pin DIN

front panel Analogue 3.5mm jack

Digital 3.5mm mini-TosLink jack

dig. 1 Digital Coaxial (RCA phono)

dig. 2 Digital Optical (TosLink)

dig. 3 Digital Coaxial (RCA phono)

dig. 4 Digital Optical (TosLink)

Note: The Phono DIN socket carries a power supply output

intended to power a Naim phono preamplifier. A turntable

cannot be used with NaimUniti 2 without an external

phono preamplifier.

Note: The front panel analogue/digital jack socket can

accept both conventional analogue 3.5mm plugs and

mini-TosLink optical digital plugs. It will automatically

identify the type of plug inserted and handle the signal

appropriately.

Always use high quality interconnect cables to connect

sources to NaimUniti 2 inputs.

2 NaimUniti 2 Installation and Connection

NaimUniti 2 should be installed on an equipment stand intended for the purpose. Do not

stand it directly on top of another item of equipment and ensure it is well ventilated. Care

should be taken to ensure that it is level. It should be installed in its final location before

connecting cables or switching on. NaimUniti 2 has no standby mode and is intended to

be left switched on.

A transit screw on the underside of the NaimUniti 2 case should be removed before use

and replaced if the unit is to be moved. This transit screw must not be used in any other

Naim product. Handle NaimUniti 2 with extra care once the transit screw is removed.

Connecting NaimUniti 2 to mains power and to a variety of audio peripherals and sources

is described in the following paragraphs. Diagram 2.1 illustrates the NaimUniti 2 rear panel

connection sockets.

2.1 NaimUniti 2 Rear Panel

mains input

and fuse

power switch

network socket

FM/DAB aerial

socket

USB update interface

remote

input (RC5)

left

speaker

right

speaker

signal ground switch

preamp output

subwoofer outputs

line

output

analogue

inputs

phono

input

digital

inputs

wireless network (Wi-

Fi) antenna socket

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim NaimUniti 2 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Naim NaimUniti 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info