Bedienungsanleitung Naim NaimUniti 2 (Seite 5 von 25) (Englisch)

707486

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

NaimUniti 2 Installation and Connection

2.4.2 Audio Signal Outputs

NaimUniti 2 provides audio signal outputs for a variety of

applications. Connections to the outputs are made via the

socket types listed in the following table:

Output Type Socket

Preamp out Analogue stereo 4-pin DIN

Sub out 1 Analogue mono RCA phono

Sub out 2 Analogue mono RCA phono

Line out Analogue stereo RCA phonos

Note: The preamp output is intended for connection to an

upgrade or second power amplifier. The output is taken

after the NaimUniti 2 volume and balance controls so a

power amplifier connected to it will respond to NaimUniti 2

volume and balance control changes. The output always

reflects the selected input signal.

Note: The two subwoofer outputs are mono and unfiltered.

They are taken after the NaimUniti 2 volume control so

subwoofers connected to them will respond to NaimUniti

2 volume control changes. The outputs always reflect the

selected input signal and can be switched on or off in the

Speakers setup menu.

Note: The stereo line output is intended to be connected

to a recording device. It is taken before the NaimUniti 2

volume and balance controls so does not reflect volume

or balance control changes. The output always reflects the

selected input signal.

2.5 Speaker Outputs

A set of stereo speaker connection sockets is provided

on the NaimUniti 2 rear panel. Custom Naim Audio

loudspeaker connectors are supplied to make the

connection and in order to comply with current European

safety regulations these should always be used. Naim

Audio speaker cable will provide the best results, however,

a range of speaker cable types may be used without

risk of damage to the amplifier. Contact your local Naim

retailer for further advice. Use equal lengths of speaker

cable for each channel.

Ensure when connecting speakers that they are “in

phase”. That is, the positive and negative connection

orientation at both the speaker and amplifier ends of the

cable is the same for both channels.

2.6 Headphone Output

NaimUniti 2 is fitted on its front panel with a 3.5mm stereo

headphone socket. Insertion of a headphone plug will

mute the speaker outputs.

Note: NaimUniti 2 controls and stores volume settings

separately for headphones and speakers.

2.7 Signal Ground Switch

NaimUniti 2 is fitted on its rear panel with a Signal Ground

switch offering two positions: Chassis or Floating. Select

the Chassis position unless NaimUniti 2 is connected

in a hi-fi system incorporating another earthed source

component, or mains “hum” is audible through the

loudspeakers. Contact your retailer, distributor or Naim for

advice if necessary.

Note: “Connected” in the context above means an

analogue audio signal cable that includes an earth

connection.

Note: All Naim CD players are earthed so the Signal

Ground switch should be set to floating if one is connected

in the system.

No damage will be done if the wrong Signal Ground

position is chosen, however the system sound quality may

be compromised.

2.7.1 General Audio Connection Notes

The NaimUniti 2 negative analogue input and output

connections for each channel are common. The mains

earth (ground) should always be connected regardless of

what other equipment is used. The mains earth primarily

grounds the case and the electrostatic screen within the

transformer, and is only connected to the signal negative if

the Signal Ground switch is set to Chassis. In order to avoid

hum loops, the signal negative of the whole system should

be connected to the mains earth in one place only.

2.8 USB/iPod Interface

NaimUniti 2 is fitted with a front panel USB interface

intended for the connection of Apple iPod models and

USB memory sticks carrying audio files. The USB interface

should not be used for any other purpose.

Depending on the setup options chosen (see Section

4.3.6), iPod batteries will be charged when connected to

the USB interface.

2.9 Network Connections

2.9.1 Wired Network Connection

NaimUniti 2 is fitted on its rear panel with a standard

RJ45 Ethernet socket. This socket enables NaimUniti 2

to join home networks via a network router to access

internet radio data streams or to play audio files stored on

appropriately configured UPnP™ servers.

Ethernet-over-mains hardware may be used and provides

a simple and convenient method of wired home network

connection. However, depending on mains wiring factors

specific to each home environment, the presence of

network data on the mains supply may compromise

overall system sound quality. If any sound quality

compromise is found to be unacceptable, dedicated

network cabling should be installed or wireless networking

should be employed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim NaimUniti 2 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Naim NaimUniti 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info