Parts supplied
𝖠 Rear view camera × 1
𝖡 RCA power supply cable × 1
𝖢 Image processing unit power supply × 1
𝖣 Button × 1
𝖤 Hexagonal × 1
𝖥 V× 1
𝖦 V× 1
𝖧 Metal × 5
𝖨 Plastic × 10
𝖩 W× 1
𝖪 Double-sided tape (rectangular) × 1
𝖫 Double-sided tape (square) × 1
𝖬 Camera stand bracket 𝖢 × 1
Installation example (Fig. 1)
① Glass
② Make sure it doesn’t touch the wiper
③ Install on the center part
Note:
• The position and angle of the image from the rear
view camera can still be adjusted using the initial
setup ev
center of the vehicle. Refer to “First
in the Owner’
Changing the orientation of camera
stand installation (Fig. 12-1)
The camera stand can be installed in
various w
which camera stand bracket 𝖡 is attached
or attaching camera stand bracket 𝖢 .
Change to match your car’
installation site.
1. Use the hexagon wrench to r
the screws securing camera stand
brackets 𝖠 and 𝖡 . (Fig. 2)
2. Change the direction of installation
bracket 𝖡 . (Fig. 3-1)
3. Reattach with the screws.
Installing Using Camera Stand Bracket 𝖢
(Fig. 12-4)
1. Use the hexagon wrench to r
the screws securing camera stand
brackets 𝖠 and 𝖡 . (Fig. 2)
2. Attach camera stand bracket 𝖢 to
the camera stand. (Fig. 3-2)
3. Attach the rear view camera to cam-
era stand bracket 𝖡 . (Fig
4. Attach the camera stand and rear
view camera. (Fig. 3-4)
Route the cables as shown in the f
that they do not become entangled.
Attach the camera stand while being
careful not to mistake the vertical
orientation
of the rear view camera. (Fig. 8)
Installation Procedure
Note:
• Before making a final installation of the unit,
temporarily connect the wiring to confirm that
the connections are correct and the system works
properly
• Use only the parts included with the unit to ensure
proper installation. The use of unauthorized parts
can cause malfunctions.
• Consult with your nearest dealer if installation
requires the drilling of holes or other
modifications of the v
• Install the unit where it does not get in the driv
way and cannot injure the passenger if there is a
sudden stop, like an emergenc
• When mounting this unit, make sure none of
the leads are trapped between this unit and the
surrounding metalwork or f
• T
processing unit power supply in places where it
might come in contact with liquids.
• Do not mount this unit near the heater outlet,
where it would be af
doors, where rainwater might splash onto it.
(Nev
because of the danger of malfunction due to high
temperatures.)
• Before drilling any mounting holes alw
behind where you want to drill the holes. Do not
drill into the gas line, brake line, electrical wiring
or other important parts.
• If this unit is installed in the passenger compartment,
anchor it securely so it does not break free while the
car is moving, and cause injury or an accident.
• If this unit is installed under a front seat, make
sure it does not obstruct seat movement. Route
all leads and cords carefully around the sliding
mechanism so they do not get caught or pinched
in the mechanism and cause a short circuit.
• Locate in the position you want to install the rear
view camera.
camera, and install so that the camera doesn’t
touch the car
• When sticking to a glass surface, stick it on in a
position that assures the camera doesn’t touch the
rear window
Installation <ENGLISH>
• Install so that it does not obstruct the rear field of
view
• Install so that it does not protrude from the side of
the car
• Do not perform installation in rain or fog.
• When humidity is high, dry the surface to which
the unit is to be attached before installing. Moisture
on the attachment surface reduces adhesi
which may lead to the unit coming off.
• Install so that the rear view camera is aligned in
parallel with the direction of vehicle mov
(straight back from the vehicle). (Fig. 4)
• Install the rear view camera abov
If the installed location of the rear view camera is
lower than the license plate, it will not be possible
to make image corrections causing distortion of the
image from the rear view camera.
• If the temperature of the attachment surface is
low
installing to improve adhesi
• Do not attach the camera stand to areas on the car
body treated with fluorocarbon resin, or glass. This
may result in the rear view camera f
• During the 24-hour period after installing:
– Do not apply water to the unit.
– Do not expose the unit to rain.
– Do not subject the camera to unnecessary force.
• Thoroughly clean where tape is used for sticking
on the unit.
1. Clean the surface to which the rear
view camera is to be installed.
(Fig. 5)
Use a cloth or other item to wipe oil, wax,
dust and any other dirt from the installation
surface.
2. Remove the r
the camera stand. (Fig. 6)
Remov
hexagon wrench pro
① To
② Rear view camera
③ Bottom
④ Installation
⑤ Camera
3. Align the camera stand with the
installation surface. (Fig. 7)
Adjust the camera stand so that there is no
space between it and the installation surface.
① T
② T
③ Camera
4. Attach the camera stand remo
step 2 to the rear view camera with
the mounting screws. (Fig
The rear view camera has a mark indicating
the top of the camera.
Attach the camera stand while being
careful not to mistake the vertical
orientation of the rear view camera.
① T
② Bottom
③ Mark
5. Peel off the sheet on the back of they
camera stand and stick it on. (Fig. 9,
Fig. 10)
Press the camera stand with your fingers to
stick it to the installation surface.
the adhesiv
on a second time reduces adhesiv
which may result in the unit coming off.
① Camera
② When sticking to the center
③ When attaching using camera stand bracket
𝖢 (attaching while rotating by 90°)
6. Adjust the angle so that the bumper
or rear edge of the car is display
at the bottom of the
(Fig. 11, Fig
① Angle of view
Horizontal:
② Angle of view
V
③ Bumper or rear edge of car
Note:
• The angle shown v
specifications.
result of image processing.
• The position and angle of the image from the
rear view camera can still be adjusted using the
initial setup ev
the car is not displayed on the bottom of the TV
screen. Refer to “First T
Manual for details.
7. Attach the image processing unit
power supply
Aff
bottom of the image processing unit power
supply
to the mounting location.
① Image processing unit power supply
② V
③ V
• Y
directly to a carpet, but do not use the soft type.
• Install the image processing unit power sup-
ply close enough for the rear view camera
cable to reach.
8. Attach the button unit (Fig
Aff
the backside of the button unit. Ne
the unit onto the location where it will
be mounted.
location where the cord is to be and then
secure the cord with the clamp.
① Double-sided tape (square)
② Button
③ Metal
Instalación <ESP
Piezas suministradas
𝖠 Cámara de vista posterior × 1
𝖡 Cable de suministro de energía RCA × 1
𝖢 Fuente de energía de la unidad de procesa-
miento de imagen × 1
𝖣 Unidad de botones × 1
𝖤 Llav× 1
𝖥 Cinta × 1
𝖦 Cinta × 1
𝖧 Abrazadera × 5
𝖨 Abrazadera × 10
𝖩 Almohadilla × 1
𝖪 Cinta de doble cara (rectangular) × 1
𝖫 Cinta de doble cara (cuadrada) × 1
𝖬 Ménsula del soporte de la cámara 𝖢 × 1
Ejemplo de instalación (Fig. 1)
① Superficie
② Asegúrese de que no toque el limpiador
③ Instale en la pieza central
Nota:
• T
imagen desde la cámara de vista posterior utilizando
la configuración inicial aunque la cámara no esté
instalada en el centro del vehículo. Para los detalles,
consulte la sección “Configuración por primera v
Cambio de la orientación de la instalación
del soporte de la cámara (Fig. 12-1)
Se puede instalar el soporte de la cámara de
varias formas, cambiando la dirección en
la cual se fija la ménsula del soporte de la
cámara 𝖡 , o fijando la ménsula del soporte
de la cámara 𝖢 . Cambie de acuerdo con a
la forma de su coche o sitio de instalación.
1. Utilice la llav
los tornillos que f𝖠
y 𝖡 del soporte de la cámara. (Fig. 2)
2. Cambie la dirección de la ménsula
de instalación 𝖡 . (Fig. 3-1)
3. V
Instalación utilizando la ménsula del
soporte de la cámara 𝖢 (Fig. 12-4)
1. Utilice la llav
los tornillos que f𝖠
y 𝖡 del soporte de la cámara. (Fig. 2)
2. Fije la ménsula del soporte de la
cámara 𝖢 al soporte de la cámara.
(Fig. 3-2)
3. Fije la cámara de vista posterior a la
ménsula del soporte de la cámara 𝖡.
(Fig. 3-3)
4. Fije el soporte de la cámara y la
cámara de vista posterior. (Fig. 3-4)
Encamine los cables como se muestra en la
figura de modo que no queden enredados.
Fije el soporte de la cámara teniendo
cuidado en no in
vertical de la cámara de vista superior
(Fig. 8)
Procedimiento de instalación
Nota:
• Antes de la instalación final de la unidad, conecte
el cableado temporalmente y confirme que las
conexiones son correctas y que el sistema trabaja
normalmente.
• Utilice solamente las partes incluídas con la unidad
para asegurar una instalación adecuada. El uso de
partes no autorizadas puede ocasionar fallas de
funcionamiento.
• Si la instalación requiere del taladrado de orificios u
otras modificaciones del v
agente o concesionario más cercano a su domicilio.
• Instale la unidad en donde no interfiera con el
conductor y no pueda lesionar al pasajero en caso
de una parada repentina, tal como una frenada de
emergencia.
• Cuando monte esta unidad, cerciórese que ninguno
de los cables queda aprisionado entre esta unidad y
accesorios o partes metálicas circundantes.
• Para prev
de energía de la unidad de procesamiento de imagen
en lugares donde pueda entrar en contacto con
líquidos.
• No monte esta unidad cerca de la salida del calefactor
en donde podría ser afectado por el calor o cerca
de las puertas, en donde la lluvia podría salpicar
sobre la misma. (Para e
funcionamiento producidos por las altas temperaturas,
evite la instalación en los lugares arriba.)
• Antes de taladrar cualquier orificio de montaje
siempre compruebe lo que hay detrás en donde
desea taladrar los orificios. No taladre en la línea
de combustible, cableado eléctrico u otras partes
importantes.
• Si esta unidad es instalada en el compartimiento de
pasajeros, fíjela se
desprenda mientras el automóvil se encuentra en
movimiento, y pueda ocasionar lesiones o accidentes.
• Si esta unidad se instale bajo un asiento delantero,
cerciórese de que no obstruye el movimiento
del asiento. Pase todos los cables y conductores
cuidadosamente a trav
deslizantes, de modo que no queden aprisionados
o atrapados en el mecanismo y ocasionen un corto
circuito.
