DE/A T/CH DE/A T/CH DE/A T/CH DE/A T/CH DE/A T/CH DE/A T/CH DE/A T/CH DE/A T/CH
Contact your local municipality for details on how to dispose
of your w orn-out product
Installation video
www .smartmaxx.info
Manufacturer / Ser vice
Smartmaxx GmbH
Inselstraße 27
D-04103 Leipzig
Hotline: +49 (0) 341 99 99 43 79
E-mail: office@smartmaxx.info
IAN 43011
For all inquiries about y our product, please have y our receipt
and the article number (e.g. IAN 12345) ready as your
proof of pur chase.
Step 4
Now place the hinge bottom parts
I
ov er the springs
K
into the hinge top parts
H
. Align the hinge bottom parts
I
to the door frame and mark the drill holes 2 and 4 (see fig. 14).
Step 5
Drill the holes with a 2.0 mm drill and screw the hinge bottom
parts
I
to the door frame with two counter sunk screws
Q
each. Hinge the door and attach the springs
K
, by pushing the
hinge cov ers
J
onto the hinge bottom parts
I
(see fig. 15).
Step 6
Secure each of the closure plates
L
with two countersunk
screw s
M
to the door frame at the height of the magnets
N
,
(see fig. 16).
Fitting the frame wit hout self-closing
mechanism
This variant does not req uire closing springs
K
.
Step 1
T wist off the points of the hinge bottom parts
I
up to the
end of the indentation (see fig. 17).
Note: Do not under any circumst ances twist off the complete
pin. Other wise you can no longer use the hinge.
Step 2
Place the hinge bottom parts
I
into the hinge top parts
H
.
Follo w steps 3 to 6 of the section on “Installing frames with a
self-closing mechanism” (without the use of springs
K
).
Cleaning and Care
Never use corr osive or abrasiv e cleaning agents.
Clean the frame using a lint-free, slightly dampened clo th.
If necessar y , use mild deter gent.
Disposal
The packaging is made entir ely of environmentally
friendly materials. Dispose of it at your local recy-
cling centre.
Step 12
Lay the fibreglass fabric
S
ov er the frame. First co ver the
upper half of the insect screen. T o do so, start attaching the
fibreglass fabric
S
onto the upper left or right edge to the
aluminium profile
C
using a click strip
G
. Continue this pro-
cedure with one of the click strips
G
on the middle bar
D
.
Now pr oceed with fitting the fibreglass fabric
S
with the
click strips
G
into the aluminium profiles
B
(see Fig. 10).
Step 13
Cut the fibreglass fabric
S
off close to the click strip
G
of
the middle bar
D
. Cut surplus fabric off using a box knife
(see fig. 10). T ake the r emaining fibreglass fabric
S
and
proceed with the low er half as with the upper half of the
insect screen in step 12 (see fig. 10).
Step 14
Push the external handle
U1
with its screw channel though the
predrilled hole in the middle bar
D
and affix it by scr ewing
the internal handle
U2
against it (see fig. 11).
Fitting the frame wit h self-closing
mechanism
Step 1
Spread the tops of the hinges
H
ev enly on the profile
B
opposite the side with the handle. Ensure that a distance of at
least 15 cm between the top and bottom edge of the fr ame
and the hinge top part
H
is kept. Drill the holes with a 2.0 mm
drill (see Fig. 12).
Step 2
First affix the hinge top parts
H
with the screw s
Q
first through
the low er drilled hole of the aluminium frame
B
of the frame
of the insect screen. Then push the springs
K
up into the hinge
top parts
H
and affix them with the screw s
Q
through the
upper drilled hole (see fig. 12).
Step 3
Place the insect screen door on y our door frame. Have a sec-
ond person help you in this if necessary . Align the side of the
insect screen door , in which the magnets
N
are fitted (handle
side), with the door frame in such a way that ca. 2.5 cm of
the longitudinal profile
B
of the insect screen door is in con-
tact with the door frame. In this way y ou utilise the optimum
closing force of the magnets
N
, (see fig. 13).
brush seal
F2
into the aluminium sill
E
in the groo ve pro vided
until the corner connector
T1
or
T2
and cut this off with an
ov erlap of 3 cm. Slide the br ush seal
F1
on the underside of
the sill
E
into the groo ve pro vided can cut this off again with
an ov erlap of 3 cm (fig. 5).
Step 6
Slide from abo ve a middle bar connector
V1
into the aluminium
profile
B
along the intended groo ve (see fig. 6 / a). Place
the corner connectors
A
with the overlapping brush seal onto
the top of the aluminium profiles
B
. Ensure that y ou place
the second magnet
N
into the corner connector
A
that will
later be opposite the hinges (see fig. 6 / b).
Step 7
Determine the position of the middle bar connector
V1
at the
middle of the two aluminium pr ofiles
B
and mark the drill
holes with a pencil. Using a 2.0 mm-drill bit, drill at this point
a hole in each profile inner surface. Fasten the middle bar
connector
V1
, using one screw
V2
through the hole drilled
pre viously through the aluminium profile
B
(see fig. 7).
Step 8
Insert the cor ner connector
A
of the aluminium profile
C
already connected to the sill
E
onto the aluminium profile
B
.
Att ach to the aluminium pr ofile
C
the rest of the brush seal
F2
and mov e the seal through to the corner connector
A
.
Again, ov erlap by about 3 cm and cut the brush seal
F2
off
(see fig. 8).
Step 9
Slide the middle bar
D
on the aluminium profile
B
mentioned
in step 8 onto the middle bar connector
V1
.
Attention: The predrilled end must on the side with the
magnet (fig. 8).
Step 10
Now finish the frame b y putting the second aluminium profile
B
onto the free ends of the aluminium profile
C
and middle
bar
D
and screw them to the sill
E
, using the T orx screws
P1
. If necessar y , user a rubber mallet to knock in the corner
brack et
A
(see fig. 8).
Step 11
Cut the long click strips
G1
into four parts, matching the top
and bottom sections of the aluminium profiles
B
. Shorten the
four click strips
G2
to the measured width (B) minus 2 cm (see
fig. 9).
Assembling the fr ame
Step 1
Measure the internal dimensions (H = height, B = width) of the
doorframe (fig. 1). Ensure the present doorframe has 30 mm
contact surface on all sides. If this sur face is not available,
adjust the dimensions individually , each to 2 cm, taking into
consideration the hinges and the magnets. Add 0.5 cm to the
measured height H and cut the aluminium profiles
B
to the
resulting length using the hacksaw and mitre bo x (fig. 1).
Deduct 2 cm from the measured width B. Using a hacksaw , cut
the aluminium profile
C
, the middle bar
D
and the alumin-
ium sill
E
to the calculated size (fig. 1). R emove burrs fr om
the cutting surface.
Step 2
Put the drilling template
O
on one end of a aluminium profile
B
and push it until impact. Drill the screw hole thr ough the
profile w all using a 4 mm drill and the drill holes on the side
of the template
O
(fig. 3a). Repeat the pr ocess with the sec-
ond aluminium profile
B
.
Attention: Drill the holes on the opposing ends so that t he
sides of the aluminium profiles
B
with the holes are mirror
inv er ted.
Step 3
Put the drilling template
O
on one end of the middle bar
D
and push until impact. Drill the screw hole thr ough the profile
D
using the dill channels B on the upper side of the template
O
to he l p yo u (ø 6.0 mm).
Step 4
Now slide the pre-drilled end of each aluminium pr ofile
B
onto the matching sill corner connector
T1
and
T2
and into
the profile opening.
Attention: Place a magnet
N
in the corner connector oppo-
site to what will later be the hinge side (see fig. 4). If necessar y ,
use a rubber mallet to position the corner connectors
T1
and
T2
. Slide the brush seal
F2
into one aluminium profile
B
from
abov e along the intended groov e until it reaches the bottom
and and already inserted corner connector
T1
and
T2
. Let
the upper end ov erlap by 3 cm and cut off the brush seal
F2
(see detailed picture fig. 4). Pr oceed with the second alumin-
ium profile
B
in the same way .
Step 5
Screw one aluminium pr ofile
B
to the aluminium sill
E
, using
the T orx screws
P1
and the T orx bit
P2
(see fig. 5). Slide the
O
1 Drilling template
P1
4 T orx screws 50 mm
P2
1 T orx bit for the Torx screw s
Q
9 Countersunk scre ws 25 mm
R
3 Countersunk scre ws 16 mm
S
1 Fibreglass fabric
T1
1 Corner connector sill lef t
T2
1 Corner connector sill right
U1
1 External handle
U2
1 Internal handle
V1
2 Bar connectors
V2
2 Middle bar screw s
1 Installation instructions
T echnical Dat a
Max assembly size: 100 x 210 cm
Max. internal size of the door frame: 94 x 204 cm
Safet y inf ormation
DANGER TO LIFE AND
RISK OF ACCIDENTS FOR INF ANTS AND
CHILDREN! N ev er leave children unattended
with the packaging material or the product. The pack ag-
ing material presents a suffocation hazard and ther e is a
risk of loss of life from str angulation. Children frequently
underestimate the dangers. Please k eep children away
from the de vice at all times. This product is not a toy .
CAUTION! RISK OF INJUR Y! Please ensure that no
parts are damaged and that all par ts are correctly assem-
ble d. Incorrect assembly could lead to injury . Damaged
parts could impact safet y and function.
Installation
Before installation, ensur e your door is suitable for this
product. Also check that your doorframe does not e xceed
the maximum dimensions.
CAUTION RISK OF INJUR Y! For the installation y ou
requir e a hacksaw , a box knife and an electric drill.
Always r efer to the operating instructions for the requir ed
tools and wear safety gloves.
Aluminium Insect Door Screen
Introduction
Congratulations! Y ou have purchased a high-quality
pr oduc t. Familiarise y ourself with the product prior
to assembly . Carefully r ead the following assembly
instructions and safet y advice. Only use the product as described
and for the indicated purpose. Keep the instructions in a safe
place, you might need them later . If y ou pass the product on
to any one else, please ensure that you also pass on all the
documentation with it.
Intended use
This product is intended to pr otect against insects and flies in
private residential ar eas. Any use other than pre viously men-
tioned or any pr oduct modification is prohibited and can lead
to injuries and / or product damage. The manufacturer is not
liable for damage caused by impr oper use. The product is
not intended for commercial use.
Description of parts and cont ents
Note: Be careful not to inadv ertently t hro w away any assembly
materials whilst unpacking. Immediately after unpacking please
check the package contents for completeness and if all parts
and the product are in good condition. Do no t assemble the
product if an y of the included items listed below are missing.
A
2 Corner connector
B
2 Aluminium profiles 2060 mm
C
1 Aluminium profile 940 mm
D
1 Middle bar 940 mm
E
1 Aluminium sill 940 mm
F1
1 Brush seal 15 mm thick
F2
1 Brush seal 5 mm thick
G1
2 Click strips long
G2
4 Click strips shor t
H
3 Hinge top part
I
3 Hinge lower part
J
3 Hinge cover s
K
3 Springs
L
2 Closure plates
M
4 Countersunk scre ws for the closure plates
N
2 Magnets
Hersteller / Ser vice
Smartmaxx GmbH
Inselstraße 27
D-04103 Leipzig
Hotline: +49 (0) 341 99 99 43 79
Mail: office@smartmaxx.info
IAN 43011
Bitte halten Sie für alle Anfragen den K assenbon und die Artikel-
nummer (z. B. IAN 12345) als Nachweis für den K auf bereit.
Rahmen ohne Selbstschließ-
mechanismus montieren
Bei dieser V ariante werden k eine Schließfedern
K
benötigt.
Schritt 1
Knipsen Sie die Spitzen der Scharnierunterteile
I
bis zum
Ende der Einkerbung ab (siehe Abb. 17).
Hinw eis: Knipsen Sie keinesfalls den k ompletten Steg ab.
Andernfalls können Sie das Scharnier nicht mehr verwenden.
Schritt 2
Stecken Sie die Scharnierunterteile
I
in die Scharnierober-
teile
H
. Befolgen Sie die Arbeitsschritte 3 bis 6 des Kapitels
„Rahmen mit Selbstschließmechanismus montieren“ (ohne
V er wendung der F edern
K
).
Reinigung und Pflege
V er wenden Sie k einesfalls ätzende oder scheuernde
Reinigungsmittel.
Reinigen Sie den R ahmen mit einem fusselfreien, leicht
angefeuchteten T uch.
V er wenden Sie ggf. ein mildes R einigungsmittel.
Entsorgung
Die V erpackung besteht aus umw eltfreundlichen
Materialien. Entsorgen Sie diese in den örtlichen
Recy clingbehältern.
Möglichkeiten zur Entsor gung des ausgedienten Produkts
erfahren Sie bei Ihrer Gemeinde oder Stadtverwaltung
Montagevideo
www .smartmaxx.info
Rahmen mit Selbstschließ-
mechanismus montieren
Schritt 1
V erteilen Sie die Schar nieroberteile
H
gleichmäßig am Profil
B
ge gen übe r der Gr iffs ei te. Achten Sie dar auf, dass zwischen
Ober- und Unterk ante von Rahmen und Scharnieroberteil
H
ein Abstand von mindestens 15 cm bleibt. Bohren Sie mit einem
2,0 mm-Bohrer die Bohrlöcher (siehe Abb. 12).
Schritt 2
Befestigen Sie die Scharnieroberteile
H
mit den Schrauben
Q
zuerst durch das unter e Bohrloch am Aluminiumprofil
B
des
Insektenschutztürrahmens. Schieben Sie dann die Federn
K
in
die Scharnieroberteile
H
hoch und fixieren diese mit den
Schrauben
Q
durch das obere Bohrloch (siehe Abb. 12).
Schritt 3
Stellen Sie die Insektenschutz-Tür an Ihren Türstock. Lassen
Sie sich bei diesem Schritt ggf. von einer zweiten P erson helfen.
Richten Sie die Seite der Insektenschutz-Tür , in der die Mag-
nete
N
montiert sind (Gr iffseite), so an Ihrem Türst ock aus,
dass ca. 2,5 cm des Längsprofils
B
der Insektenschutz-Tür
am Türstock aufliegen. Somit nutzen Sie die optimale Schließ-
kraft der Magnete
N
aus (siehe Abb. 13).
Schritt 4
Stecken Sie nun die Scharnierunterteile
I
über die Federn
K
in die Scharnieroberteile
H
. Halten Sie die Scharnierunter-
teile
I
an den Türstock an und markieren Sie die Bohrlöcher
2 und 4 (siehe Abb. 14).
Schritt 5
Bohren Sie mit einem 2,0 mm-Bohrer die Bohrlöcher und
schrauben Sie die Scharnierunterteile
I
mit je zwei Senk -
kopfschr auben
Q
an den Türstock. Fixieren Sie die F edern
K
, indem Sie die Scharnier- Abdeckkappen
J
auf die
Scharnierunter teile
I
aufstecken (siehe Abb. 15).
Schritt 6
Fixieren Sie die Schließplatten
L
mit je zwei Senkk opfschrau-
ben
M
am Türstock in Höhe der Magnete
N
(siehe Abb. 16).
Achtung: Das vorgebohrte Ende muss auf der Magnetseite
liegen (Abb. 8).
Schritt 10
Stellen Sie nun den Rahmen fertig, indem Sie das zweite Alu-
miniumprofil
B
auf die freien Enden v on Aluminiumprofil
C
und Mittelsprosse
D
aufstecken und mit dem Aluminium-T ritt-
blech
E
mittels den T orx-Schrauben
P1
verschr auben. V er-
wenden Sie zum Einklopfen des Eckv erbinders
A
ggf. einen
Gummihammer (siehe Abb. 8).
Schritt 11
Schneiden Sie die langen Clickleisten
G1
in vier T eile, passend
für den oberen und unteren Ber eich der Aluminiumprofile
B
,
zu. K ürzen Sie die vier Clickleisten
G2
auf die gemessene
Breite (B) minus 2 cm (siehe Abb. 9).
Schritt 12
Legen Sie das Fiberglasge webe
S
über den Rahmen.
Bespannen Sie erst die obere Hälfte des Insektenschutzrah-
mens. Beginnen Sie hierzu am oberen link en oder rechten
Rand, das Fiber glasgewebe
S
mit einer Clickleiste
G
im
Aluminiumprofil
C
zu fixieren. Setzen Sie diesen V organg
mit einer Clickleiste
G
an der Mittelsprosse
D
fort. Befesti-
gen Sie nun mit den Clickleisten
G
das Fiberglasge webe
S
in der oberen Hälfte des Rahmens links und r echts in den
Aluminiumprofilen
B
(siehe Abb. 10).
Schritt 13
Schneiden Sie das Fiberglasge webe
S
dicht an der Click-
leiste
G
der Mittelsprosse
D
ab. Entfernen Sie überstehendes
Gew ebe mit einem T eppichmesser (siehe Abb. 10). Nehmen
Sie das verbleibende Fiber glasgewebe
S
und verfahren Sie
mit der unteren Hälfte des Insektenschutzrahmens wie mit der
oberen Hälfte in Schritt 12 (siehe Abb. 10).
Schritt 14
Stecken Sie den Außengriff
U1
mit dem Schraubk anal durch
das vor gebohr te Loch der Mittelsprosse
D
und befestigen
diesen, indem Sie den Innengriff
U2
von hinten gegenschrauben
(siehe Abb. 11).
ein Aluminiumprofil
B
die Bürstendichtung
F2
von oben in
die dafür vor gesehene Nut bis unten an den bereits einge-
setzten Eckverbinder
T1
und
T2
ein. Lassen Sie am oberen
Ende 3 cm überstehen und schneiden die Bürstendichtung
F2
ab (siehe Detailbild Abb. 4). V erfahren Sie mit dem zweiten
Aluminiumprofil
B
ebenso.
Schritt 5
V erschrauben Sie ein Aluminiumpr ofil
B
mit dem Alumini-
um-T rittblech
E
unter V er wendung der T orx-Schrauben
P1
un d des T or x-Einsatzes
P2
(siehe Abb. 5). Schieben Sie die
Bürstendichtung
F2
in das Aluminium-T rittblech
E
in die
dafür vor gesehene Nut bis in den Eckverbinder
T1
bzw .
T2
ein und schneiden diese mit einem Überstand von 3 cm ab.
Schieben Sie die Bürstendichtung
F1
an der Unterseite des
T rittblechs
E
in die vor gegebene Nut ein und schneiden
diese wieder mit einem Überstand von 3 cm ab (Abb. 5).
Schritt 6
Schieben Sie je Aluminiumprofil
B
von oben einen
Mittel-
sprossen verbinder
V1
in die dafür vor gesehene Nut ein (siehe
Abb. 6/a).
Setzen Sie die Eckverbinder
A
unter Mitnahme
der überstehenden Bürstendichtung oben in die Aluminium-
profile
B
ein. Achten Sie darauf, dass Sie in den Eckverbin-
der
A
, welcher der später en Scharnierseite gegenüber liegt,
den zweiten Magnet en
N
einlegen (siehe Abb. 6/b).
Schritt 7
Legen Sie an den beiden Aluminiumprofilen
B
mittig die
P osition für die Mittelsprossenv erbinder
V1
fest und markieren
Sie die Bohrpunkte mit einem Stif t. Bohren Sie dort mit einem
2,0 mm-Bohrer jew eils ein Loch in die Profilinnenseite. Befestigen
Sie den Mittelsprossen verbinder
V1
mit einer Schraube
V2
durch das zuv or gebohr te Loch am Aluminiumprofil
B
(siehe
Abb. 7).
Schritt 8
Stecken Sie das Aluminiumpr ofil
C
auf den Eckverbinder
A
des bereits mit dem T rittblech
E
montierten Aluminiumprofils
B
auf. V ersehen Sie das Aluminiumprofil
C
mit der restlichen
Bürstendichtung
F2
und schieben diese bis in den Eckverbin-
der
A
durch. Lassen Sie wieder ca. 3 cm überstehen und
schneiden die Bürstendichtung
F2
ab (siehe Abb. 8).
Schritt 9
Stecken Sie auf das in Schritt 8 genannte Aluminiumprofil
B
die Mittelsprosse
D
auf den Mittelsprossen verbinder
V1
auf.
VORSICHT VERLETZUNGSGEFAHR! Für die Mon-
tage benötigen Sie eine Eisensäge, ein T eppichmesser
und eine Bohrmaschine. Ziehen Sie unbedingt die
Bedienungsanleitungen der benötigten W erkzeuge hinzu
und verwenden Sie Schutzhandschuhe.
Rahmen montieren
Schritt 1
Messen Sie die Innenmaße (H = Höhe, B = Breite) des Türstock s
(Abb. 1). Achten Sie auf eine vorhandene Türstock - Auflage-
fläche von 30 mm an allen Seiten. Ist diese Fläche nicht v or -
handen, passen Sie die Maße individuell, unter Berücksichtigung
der Scharniere und der Magnete, mit jew eils 2 cm an. Addieren
Sie zu der gemessenen Höhe H 0,5 cm und kürzen die Alumi-
niumprofile
B
mittels Eisensäge und Gehrungslade auf das
ermittelte Maß (Abb. 1). Ziehen Sie von der gemessenen
Breite B 2 cm ab. K ürzen Sie mit der Eisensäge das Aluminium-
profil
C
, die Mittelsprosse
D
und das Aluminium-T rittblech
E
auf das ermittelte Maß (Abb.1). Entgraten Sie die Schnitt-
flächen.
Schritt 2
Setzen Sie die Bohrschablone
O
auf einem Ende eines Alu-
miniumprofils
B
auf und schieben es bis zum Anschlag vor .
Bohren Sie mit einem 4 mm-Bohrer mit Hilfe der seitlichen
Bohrlöcher an der Schablone
O
das Schraubloch durch die
Profilw ände durch (Abb. 3a). Wiederholen Sie den V organg
beim zweiten Aluminiumpr ofil
B
.
Achtung: Setzen Sie hier die Bohrlöcher am entgegenge-
setzten Ende, so dass die mit den Bohrungen versehenen Seiten
der Aluminiumprofile
B
spiegelverk ehr t zueinander liegen.
Schritt 3
Setzen Sie nun die Bohrschablone
O
auf die Mittelsprosse
D
an einem Ende auf und schieben sie bis zum Anschlag vor .
Bohren (ø 6,0 mm) Sie mit Hilfe des Bohrkanals B auf der Ober-
se it e der Schablone
O
das Schraubloch durch das Pr ofil
D
.
Schritt 4
Schieben Sie nun je Aluminiumprofil
B
am vor gebohr ten Ende
den jew eils passenden Eckverbinder T rittblech
T1
und
T2
in
die Profilöffnung ein.
Achtung: Legen Sie in den Eckverbinder , der gegenüber
der späteren Scharnierseite liegt, einen Magneten
N
ein
(siehe Abb. 4). V er wenden Sie zum Einbringen der Eckver-
binder
T1
und
T2
ggf. einen Gummihammer . Schi eben Sie in
K
3 Federn
L
2 Schließplatten
M
4 Senkkopfschrauben für Schließplatten
N
2 Magnete
O
1 Bohrschablone
P1
4 T orxschrauben 50 mm
P2
1 T orxbit für Torxschrauben
Q
9 Senkkopfschrauben 25 mm
R
3 Senkkopfschrauben 16 mm
S
1 Fiberglasge webe
T1
1 Eckverbinder T rittblech links
T2
1 Eckverbinder T rittblech rechts
U1
1 Außengriff
U2
1 Innengriff
V1
2 Sprossen verbinder
V2
2 Schrauben Sprossen verbinder
1 Montageanleitung
T echnisc he Daten
Max. Bausatzmaß: 100 x 210 cm
Max. Innenmaß des Türstocks: 94 x 204 cm
Sicherheitshinweise
LEBENS- UND UNF ALL-
GEFAHR FÜR KLEINKINDER UND KIN -
DER! Lassen Sie Kinder niemals unbeaufsichtigt
mit V erpackungsmaterial und Produkt. Es besteht Ers tickungs-
ge fa hr durch V erpackungsmaterial und Lebensgefahr
durch Strangulation. Kinder unter schätzen häufig die
Gefahren. Halten Sie Kinder stets v om Produkt fern. Das
Produkt ist k ein Spielzeug.
VORSICHT! VERLETZUNGSGEFAHR! Stellen Sie
sicher , dass alle T eile unbeschädigt und sachgerecht
montiert sind. Bei unsachgemäßer Montage besteht Ver -
letzungsgefahr . Beschädigte T eile können die Sicherheit
und Funktion beeinflussen.
Montage
V erge wissern Sie sich vor der Montage, dass Ihre Tür für
dieses Produkt geeignet ist. Überprüfen Sie auch, dass
Ihr Türstock die Maximalmaße nicht überschreitet.
Alu-Insektensc hutz-Tür
Einleitung
Herzlichen Glückwunsch! Mit Ihrem Kauf haben Sie
sich für ein hochwertiges Produkt en tschie den.
Machen Sie sich vor der Montage mit dem Produkt
vertraut. Lesen Sie hierzu aufmerksam die nachfolgende
Montageanleitung und die Sicherheitshinweise. Benutz en Sie
das Produkt nur wie beschrieben und für die angegebenen
Einsatzbereiche. Bew ahren Sie die Anleitung gut auf. Händi-
gen Sie alle Unterlagen bei W eitergabe des Pr oduktes an
Dritte mit aus.
Bestimmungsgemäßer Gebr auch
Dieser Artikel ist als Schutz gegen Insekten und Fliegen im
privaten W ohnber eich vorgesehen. Eine andere V erwendung
als zuvor beschrieben oder eine V eränderung des Pr oduktes
ist nicht zulässig und kann zu V erletzungen und / oder Be sc hä-
digungen des Produkts führ en. Für aus bestimmungswidriger
V er wendung entstandene Schäden übernimmt der Hersteller
keine Haftung. Das Produkt ist nicht für den ge werblichen
Einsatz bestimmt.
T eilebeschr eibung und Lieferumfang
Hinw eis: Achten Sie beim Auspacken darauf, dass Sie nicht
versehentlich Montagematerial w egwerfen. Kontr ollieren Sie
unmittelbar nach dem Auspacken den Lieferumfang auf V oll-
ständigkeit so wie den einw andfreien Zustand des Produktes
und aller T eile. Montieren Sie das Pr odukt keinesfalls, wenn
der Lieferumfang nicht vollständig ist.
A
2 Eckverbinder
B
2 Aluminiumprofile 2060 mm
C
1 Aluminiumprofil 940 mm
D
1 Mittelsprosse 940 mm
E
1 Aluminium-T rittblech 940 mm
F1
1 Bürstendichtung 15 mm Stärke
F2
1 Bürstendichtung 5 mm Stärke
G1
2 Clickleisten lang
G2
4 Clickleisten kurz
H
3 Scharnieroberteile
I
3 Scharnierunter teile
J
3 Scharnierabdeckkappen
GB GB GB GB GB GB GB
IAN 43011
Smartmaxx GmbH
Inselstraße 27
D-04103 Leipzig
V ersion des informations
Stand der Informationen
Last information update: 09 / 2013
Ident.-No.: QA271092013-2
2
43011_pow_Alu_Insektenschutz-Tuer_LB2.indd 2 16.09.13 12:47