581328
3
Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
Program
Weekday
AM/PM mode
Time
Relative Humidity
3
4
HEAT/COOL CONTROL
LCD DISPLAY
DISPLAY
UP
DOWN
FAN CONTROL
SET CLOCK
PROGRAM
AHEAD
RESET
HOLD
BACK
USAGE
Function Key Descriptions
LCD Display
26
Set Time and Day
Press SET CLOCK to start time setting. The time and SET symbol will flash.
Use AHEAD or BACK to set the current time.
Press SET CLOCK again. The day and SET symbol will flash.
Use AHEAD or BACK to set the current day.
Press SET CLOCK again to exit.
INSTALLING THE BATTERY
SELECT C / F display
Install the two AA size batteries (included) to the thermostat following the polarity as marked. The LCD
display will show the room temperature flashing in Celsius. Press UP or DOWN to change the
temperature display between C and F.
Press SET CLOCK, and the thermostat would go to clock setting / normal display.
Note: This is a one-time process. The temperature unit of the thermostat CANNOT be changed
afterwards unless you reset the thermostat.
Attaching The Thermostat To The Back-Cover
Attach the thermostat body to the back-cover that is already installed on the wall by snapping the
hinges together. Flip up the thermostat and it will snap close.
Congratulations! You have completed the installation of the thermostat. Please refer to the operations
manual for programming and operating instructions.
°°
°°
Set / Program
Temperature
Curent Temperature
25
+
+
-
-
HE
HG
+
_
Setting The Fan Operation Jumper
Depending on your home's heating system, you may
need to change the jumper setting for the fan
operation. The jumper is located at the lower right-
hand side of the back of the thermostat.
HG – Use this setting for gas or oil-fired furnaces.
This setting allows the fan operation to be controlled
by the heating system; not the thermostat. This is the
correct setting for most systems.
HE – Use this setting for electric heating systems. With this setting, the thermostat will turn on the fan
immediately with the heating system.
The jumper is pre-installed in the 'HG' position as a factory default. So there is no need to change
the jumper if this is the correct setting.
To change the jumper setting, pull out the small black rectangular block and align it to the new
position and push it in fully.
RC
RH
Y
W
H2
H1
B
O
G
3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für UPM THM302M wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von UPM THM302M

UPM THM302M Bedienungsanleitung - Französisch - 8 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info