Bedienungsanleitung Yaesu FT-897D (Seite 50 von 76) (Englisch)

478500

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Page 48 FT-897D OPERATING MANUAL

SCANNING OPERATION

SCANNING FEATURES

Scan-Resume Choices

Scanning operation requires that you have the FT-897D’s

audio squelched. The transceiver then “assumes” that the

opening of the squelch corresponds to the discovery of a

signal you may wish to listen to.

Once the scan has been halted, one of three things may hap-

pen:

TIME (default action): In this mode, the transceiver pauses

on the signal and stays locked on its frequency for

five seconds. Thereafter, scanning will resume

whether or not the other station’s transmission has

ended. The pause time is adjustable from 1 to 10 sec-

onds via Menu Mode No-078

[

SCAN RESUME

]

BUSY:In this mode, the scanner will halt until the other

station’s transmission ceases (at which point the

squelch will close). One second after the squelch

closes, scanning resumes automatically.

STOP:In this mode, the scanner will find a signal, and lock

on that frequency without resuming the scan.

To choose the Scan-Resume mode:

1. Press and hold in the

[

]

button for one second to acti-

vate the Menu mode.

2. Rotate the MEM/VFO CH knob to select Menu Mode

No-077

[

SCAN MODE

]

3. Rotate the DIAL knob to select the desired Scan-Resume

mode.

4. Press and hold in the

[

]

button for one second to exit

the Menu mode.

This transceiver contains a wide variety of scanning capa-

bilities. Whether you are in the VFO mode or one of the

memory modes, scanning operation is fundamentally iden-

tical in all configurations, but with the following differences:

❒ In the VFO mode, scanning causes the transceiver to

sweep up or down the band, pausing or halting on any

signal encountered;

❒ In the Memory mode, the scanner will scan the pro-

grammed memories, and can be instructed to skip cer-

tain memories during scanning;

❒ In the Programmable Memory Scan (PMS) mode, the

scanner will scan the band within user-programmed fre-

quency limits.

Scanning Operation

In order for the FT-897D to scan automatically, the Squelch

must be set so that the background noise is silenced, be-

cause the command to “Stop Scanning” driven by the same

circuit that causes the green “Busy” LED to light up (when

noise or a signal is received).

1. Set the SQL knob to the point where background noise

is silenced. A typical setting, for effective scanning op-

eration, will be at 12 o’clock or slightly clockwise from

this position.

2. Set the transceiver into the operating configuration in

which you wish to scan (VFO or Memory; PMS will be

described later).

3. Press the

[

]

key momentarily, then rotate the MEM/

VFO CH knob, as needed, until Multi Function Row

“g”

[

SCN, PRI, DW

]

appears on the display.

4. Press the

[

](

SCN

)

key momentarily to start upward scan

(toward higher frequencies or higher memory channel

numbers).

5. Rotate the DIAL knob or MEM/VFO CH knob counter-

clockwise to toggle the scanning direction downward.

6. The scanner will now cause the transceiver to increment

in the chosen direction until a signal is detected. When a

signal is encountered which opens the Squelch, it will

do different things, depending on the operating mode:

❍ In the FM/AM modes, the transceiver pauses on the

signal and stays locked on its frequency for five sec-

onds. Thereafter, scanning will resume whether or

not the other station’s transmission has ended. While

the transceiver is in the “Pause” condition, the deci-

mal points in the frequency display area will blink.

See “Scan-Resume Choices” on next chapter for de-

tails of how to customize the resumption of scanning.

❍ In the SSB/CW modes, the scanner will slow down

(but wonn’t stop).

Press the PTT switch on the microphone to cancel scanning.

You may also press and hold in either the [UP]

or [DWN] key on the microphone for one sec-

ond to initiate upward or downward scanning,

respectively, if Menu Mode No-058 [MIC SCAN] is set to

“ON.”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FT-897D Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info