674740
110
Zoom out
Zoom in
Vorherige Seite
1/154
Nächste Seite
Page 108 FT-991 OperaTing Manual
MeMory ScAn
1. Set the transceiver to the “Memory” mode by press-
ing the
V/M
button, if necessary.
2. Press the
F(M-LIST)
button, then touch
[
SQL
]
on
the LCD. Rotate the
MULTI
knob so that the back-
ground noise is just silenced.
V/M ButtonMULTI Knob
F(M-LIST) Button
3. Press and hold in the microphone
UP
or
DWN
but-
ton for one second, or press the
F(M-LIST)
button
followed by
[
SCAN
]
to start scanning in the speci-
ed direction.
Advice:
If the scanner halts on an incoming signal, the
decimal point between the “MHz” and “kHz”
digits of the frequency display will blink.
If the incoming signal disappears, scanning will
resume in about ve seconds.
4. To cancel scanning, press the
PTT
switch, or touch
[
SCAN
]
on the LCD.
Advice:
During Memory Group operation, only the channels
within the current Memory Group will be scanned.
If the scan has paused on a signal, pressing the mi-
crophone
UP
or
DWN
button, or touching
[
SCAN
]
on the LCD will cause scanning to resume instantly.
If you press the microphone
PTT
button during
scanning, the scanner will halt at once. However,
pressing the
PTT
button during scanning will not
cause transmission.
The manner in which the scanner resumes after it has
paused on a signal may be selected by using Menu
item “
038 MIC SCAN RESUME
”. During memory
scanning, the default
TIME
(5 sec) setting will
cause the scanner to resume scanning after ve sec-
onds; however the scan may be set, to resume only
after the received signal has dropped out.
If the Main Tuning Dial knob is rotated while scan-
ning is in progress, the memory channel scanning
will continue up or down in accordance with the di-
rection of the Dial Knob rotation. (In other words, if
the dial is rotated to the left when scanning toward a
higher channel number, the direction of the scan will
reverse.)
quick point:
If you have no interest in scanning, and wish to prohibit
the microphone
UP
/
DWN
buttons from initiating scan-
ning, you may disable scanning control from the mi-
crophone using Menu item
037 MIC SCAN
(set it to
DISABLE
”).
vfo anD MeMorY scanninG
110

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu FT-991 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info