Bedienungsanleitung Dolmar ES-2146 TLC (Seite 10 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

599928

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

................ Wear safety gloves!

................ Withdraw the mains plug!

................. First aid

........ Maximum permissible length of cut

........ Direction of chain travel

.................. Chain oil

.......... Chain brake released

.......... Chain brake applied

................ Prohibited!

............... Only for EU countries

Do not dispose of electric equipment

together with household waste material!

In observance of the European Directive,

on Waste Electric and Electronic

Equipment and its implementation in

accordance with national law, electric

equipment that have reached the end of

their life must be collected separately and

returned to an environmentally

compatible recycling facility.

Intended use ENE085-1

The tool is intended for cutting lumbers and logs.

Power supply

ENF002-2

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated and can, therefore, also be used from

sockets without earth wire.

General Power Tool Safety

Warnings GEA010-1

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

Chain saw safety warnings

GEB037-8

1. Keep all parts of the body away from the saw

chain when the chain saw is operating. Before you

start the chain saw, make sure the saw chain is

not contacting anything. A moment of inattention

while operating chain saws may cause entanglement

of your clothing or body with the saw chain.

2. Always hold the chain saw with your right hand on

the rear handle and your left hand on the front

handle. Holding the chain saw with a reversed hand

configuration increases the risk of personal injury and

should never be done.

3. Hold the power tool by insulated gripping surfaces

only, because the saw chain may contact hidden

wiring or its own cord. Saw chains contacting a “live”

wire may make exposed metal parts of the power tool

“live” and could give the operator an electric shock.

4. Wear safety glasses and hearing protection.

Further protective equipment for head, hands,

legs and feet is recommended. Adequate protective

clothing will reduce personal injury by flying debris or

accidental contact with the saw chain.

5. Do not operate a chain saw in a tree. Operation of a

chain saw while up in a tree may result in personal

injury.

6. Always keep proper footing and operate the chain

saw only when standing on fixed, secure and level

surface. Slippery or unstable surfaces such as

ladders may cause a loss of balance or control of the

chain saw.

7. When cutting a limb that is under tension be alert

for spring back. When the tension in the wood fibres

is released the spring loaded limb may strike the

operator and/or throw the chain saw out of control.

8. Use extreme caution when cutting brush and

saplings. The slender material may catch the saw

chain and be whipped toward you or pull you off

balance.

9. Carry the chain saw by the front handle with the

chain saw switched off and away from your body.

When transporting or storing the chain saw

always fit the guide bar cover. Proper handling of

the chain saw will reduce the likelihood of accidental

contact with the moving saw chain.

10. Follow instructions for lubricating, chain

tensioning and changing accessories. Improperly

tensioned or lubricated chain may either break or

increase the chance for kickback.

11. Keep handles dry, clean, and free from oil and

grease. Greasy, oily handles are slippery causing loss

of control.

12. Cut wood only. Do not use chain saw for purposes

not intended. For example: do not use chain saw

for cutting plastic, masonry or non-wood building

materials. Use of the chain saw for operations

different than intended could result in a hazardous

situation.

13. Causes and operator prevention of kickback:

Kickback may occur when the nose or tip of the guide

bar touches an object, or when the wood closes in and

pinches the saw chain in the cut.

Tip contact in some cases may cause a sudden

reverse reaction, kicking the guide bar up and back

towards the operator.

Pinching the saw chain along the top of the guide bar

may push the guide bar rapidly back towards the

operator.

Either of these reactions may cause you to lose

control of the saw which could result in serious

personal injury. Do not rely exclusively upon the safety

devices built into your saw. As a chain saw user, you

should take several steps to keep your cutting jobs

free from accident or injury.

Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be

avoided by taking proper precautions as given below:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar ES-2146 TLC Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dolmar ES-2146 TLC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info