Bedienungsanleitung Dremel 1800 (Seite 6 von 76) (Englisch, Französisch, Spanisch)

32279

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Additional Safety Rules

d. Avoid awkward hand positions where a sudden slip could

cause a hand to move into the blade.

•

ALWAYS adjust the drop foot to just clear the workpiece to

protect the operator, keep blade breakage to a minimum

and provide maximum support for blade.

• Always adjust blade tension correctly.

•

The Scroll Station should cut on the down stroke. Always

make sure blade teeth are oriented downward toward

table.

• When cutting a large piece of material, make sure it is sup-

ported at table height.

• Hold the work firmly against the table.

• Do not feed the material too fast while cutting. Only feed

the material fast enough so that the blade will cut. Keep

fingers away from the blade.

• Use caution when cutting off material which is irregular in

cross section‚ it could pinch the blade before the cut is

completed. A piece of molding, for example, must lay flat

on the table and not be permitted to rock while being cut.

• Use caution when cutting off round material such as dowel

rods or tubing. They have a tendency to roll while being

cut, causing the blade to “bite”.

e. Never leave the Scroll Station running unattended. Turn

the saw OFF, make sure the saw has come to a complete

stop, and then remove plug from power supply before

leaving the work area.

f. Do not perform layout, assembly or setup work on the

table while the cutting tool is operating.

g. Turn saw off and remove plug from power supply outlet

before installing or removing an accessory attachment.

h. Access Door must be closed before operation.

i. Quick Release Tension Lever should be in down position

before operating.

THINK SAFETY

SAFETY IS A COMBINATION OF OPERATOR COMMON

SENSE AND ALERTNESS AT ALL TIMES WHEN THE Scroll

Station IS BEING USED.

Do not allow familiarity (gained from frequent

use of your Scroll Station) to become com-

monplace. Always remember that a careless fraction of a

second is sufficient to inflict severe injury.

The operation of any power tool

can result in foreign objects being

thrown into the eyes, which can

result in severe eye damage.

Always wear safety goggles that

comply with ANSI Z87.1 before

commencing power tool operation.

Some dust created by power sanding, sawing,

grinding, drilling,and other construction activi-

ties contains chemicals known to cause cancer, birth defects

or other reproductive harm. Some examples of these chem-

icals are:

• Lead from lead-based paints,

• Crystalline silica from bricks and cement and other

masonry products, and

• Arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work

with approved safety equipment, such as those dust

masks that are specially designed to filter out microscopic

particles.

NOTE AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS

THAT APPEAR ON THE PANEL ON SCROLL STATION HOUSING:

WARNING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dremel 1800 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info