Bedienungsanleitung Dremel 1800 (Seite 7 von 76) (Englisch, Französisch, Spanisch)

32279

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Specifications

General Specifications

Voltage Rating . . . . . . . . . . . . . . . . . . . . . . . . .120 V, 60 Hz

Amperage Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.6 A

No Load Speed . . . . . . . . . . . . . . .N

500-1,700/min (SPM)

Throat

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18"

Blade . . . . . . . . . . . . . . . . . . . . . . . . . .5” plain and pin-end

Blade Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3/4"

Cutting Capacity . . . . . . . . . . . . . . . . . . .1ﬂ" at 0°, 1" at 45°

Motor Specifications

In the event of a malfunction or breakdown, grounding pro-

vides a path of least resistance for electric current to reduce

the risk of electric shock.

This Scroll Station is designed to use a variable speed RPM

motor. It is wired for operation on 110-120 volts, 60 Hz. alter-

nating current. Before connecting the motor cord to wall out-

let, make certain the power switch is in the OFF position and

be sure the electric current is of the same characteristics as

stamped on the Scroll Station nameplate.

Connection To A Power Source

This machine must be grounded while in use to protect the

operator from electric shock.

Plug power cord into a 110-120V properly grounded type out-

let protected by a 15-amp dual element time delay fuse or cir-

cuit breaker.

Not all outlets are properly grounded. If you are not sure that

your outlet, as pictured on this page, is properly grounded;

have it checked by a qualified electrician.

To avoid electric shock, do not touch the

metal prongs on the plug when installing or

removing the plug to or from the outlet.

Failure to properly ground this power tool can

cause electrocution or serious shock, particu-

larly when used near metal plumbing or other metal objects.

If shocked, your reaction could cause your hands to hit the

tool.

If power cord is worn, cut or damaged in any

way, have it replaced immediately to avoid

shock or fire hazard.

DANGER

Your unit is for use on 120 volts; it has a plug that looks like

the one in Figure 1.

This power tool is equipped with a 3-conductor cord and this

plug requires a mating 3-conductor grounded type outlet as

shown. It must be grounded in accordance with all local codes

and ordinances.

If the outlet you are planning to use for this power tool is of the

two-prong type, DO NOT REMOVE OR ALTER THE GROUND-

ING PRONG IN ANY MANNER. Have a qualified electrician

replace the TWO-prong outlet with a properly grounded

THREE-prong outlet.

Improper connection of the equipment-grounding conductor can

result in a risk of electric shock. If repair or replacement of the

electric cord or plug is necessary, do not connect the equipment-

grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the

grounding instructions are not completely understood, or if in

doubt as to whether the tool is properly grounded.

Always use proper extension cord. The use of any extension

cord will cause some loss of power. To keep this to a minimum

and to prevent overheating and motor burn-out, use the table

below to determine the minimum wire size (A.W.G.) extension

cord. Use only 3-wire extension cords which have 3-prong

grounding type plugs and 3-pole receptacles which accept the

tool’s plug. Make sure your extension cord is in good condition.

Extension Cord Length

Wire Size A.W.G.

0-25 feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

26-50 feet

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

51-100 feet

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SAVE THESE INSTRUCTIONS

Figure 1. Grounded Wall Outlet

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dremel 1800 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info