Did you press the [t] button?Press the [t] button to turn the power on.
Are all of the indicators off?The power cable is not connected correctly or power is not being supplied.
Disconnect and then reconnect the power cable. sQuick Start Guide
Check the breaker and so on to ensure power is being supplied.
If the lamp cover or the lamp are not installed correctly, the lamp will not turn on.
Check that the lamp cover and lamp are installed properly. sp.111
Do the indicators turn on and off when the power cable is touched?There is probably a poor contact in the power cable, or the power cable may be defective. Reinsert the power cable. If this
does not solve the problem, stop using the projector, disconnect the power cable from the electrical outlet, and contact
your local dealer or the nearest address provided in the Support and Service Guide.
s
Epson Projector Contact List
Is Control Panel Lock set to Full Lock?Press the [t] button on the remote control. If you do not want to use Control Panel Lock, change the setting to Off.
sSettings Menu - Control Panel Lockp.52
Is the correct setting for the remote receiver selected?Check the Remote Receiver setting from the Configuration Menu. sSettings Menu - Remote Receiverp.76
Problems relating to monitoring and control
Mail is not received even if an error occurs with the projector
CheckRemedy
Is the Wireless LAN unit installed?
For wireless LAN
Check that the optional Wireless LAN unit is installed in the projector properly.
Is the network cable connected correctly?
For wired LAN
Check that the network cable is connected correctly. Reconnect it if it is not connected or not connected properly.
Are the network connection settings correct?Check the projector's network settings. sp.80
Is Standby Mode set to Communication On?To use Mail Notification when the projector is in a standby state, set Standby Mode to Communication On from the
Configuration Menu. sExtended menu - Standby Modep.78
Beim Einschalten blinkt die grüne Lampe. Lampe wurde gewechselt und funktionierte. Lampenstundenzäher wurde auf 0 gesetzt. Welchen Grund?
Eingereicht am 12-7-201709:45
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Epson eb 450w wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.