ClEl
■
∆ΗΛΩΣΗ ΣΥΜΜΡΦΩΣΗΣ
(
GR
)
∆ηλώυµε υπευθύνω τι τ πριν αντ είναι
κατασκευασµέν σύµωνα µε τν εή
Καννισµύ ή Κατασκεναστικε σνστάσει:
IEC1029-2-4, EN61029-1, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3
Κατά τι διατάει των Καννισµών τη Κινή Αγρά:
89/392/EEC
73/23EEC
89/336/EEC
απ 01-07-1999
GENEMUIDEN NL
G.M. Ensing
Quality department
28 Ferm
- Attach the sanding paper by loosening the but-
ton in the unit (at the top left) and pushing
downwards the spring.
- Stretch the sanding paper as written herunder.
- Close the cover with help of the three screws.
MOUNTING OF THE SANDING PAPER
- Loosen the knurled knob (A) (see fig. 3), but do
not remove it.
- Place the belt on both rolls. Use your left hand
to compress spring (B) so the belt can be placed
easily.
Correct assembly of the sanding belt pre-
vent unnecessary wear. The sanding belt
has to be assembled as shown in fig 4. With
your hand you can feel which part of the
sanding belt is on top of the weld.
- Retighten the knurled knob and turn over the
sanding belt a view times with your hands.
- If the sanding belt runs of or runs out of line
then use adjustment screw (C) to adjust the san-
ding belt correctly.
- Put the belt under tension by means of nut (D).
ADJUSTING THE TOOL REST
Disconnect the machine and make sure the
sanding belt has stopped before adjusting
the tool rest.
- Loosen nut (E) (see fig. 3) with a spanner.
- Move the tool rest (F) keeping a clearance
between the tool rest and the sanding belt
through which the belt just runs free.
- Retighten nut (E).
- The tool rest can be assembled at two places
depending on the application.
9. MAINTENANCE
While maintaining and cleaning the
machine pull the plug from the mainssoc-
ket. Never use water or other agressive
liquids to clean the machine. Clean the
machine by brushing it with a brush.
REGULAR MAINTENANCE OF YOUR MACHI-
NE PREVENTS PROBLEMS:
- Keep the outside of the belt sander/grinder clean
to ensure accurate operation of all moving parts
and prevent excessive wear.
- Replace the grinding stone and sanding belt
when they are worn.
- There is no need to lubricate the transport rol-
lers of the machine.
10. MALFUNCTION
Below we have listed a number of possible causes
and corresponding solutions in case the machine
does not function as it should:
1. The tool does not work when switched on.
Damaged cord and/or plug.
- Check cord and/or plug.
Defective switch.
- Contact your local Ferm dealer to have the switch
inspected and/or repaired.
2. The temperature of the electric motor
exceeds 70°C.
The motor is defective.
- Contact your local Ferm dealer to have the tool
inspected and/or repaired.
ClEl
■
DECLARATION OF CONFORMITY
(
GB
)
We declare under our sole responsibility that this
product is in conformity with the following
standards or standardized documents
IEC1029-2-4, EN61029-1, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3
in accordance with the regulations.
98/37/EEC,
73/23/EEC,
89/336/EEC
from 26-05-1998
GENEMUIDEN NL
G.M. Ensing
Quality department
