Bedienungsanleitung Fluke 289 (Seite 60 von 88) (Englisch)

763957

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

287/289

Users Manual

saved under the name of Save-2. The auto-incrementing number

can be reset to 1 by positioning the menu selector next to the

save name and then pressing the softkey labeled Reset #.

To save a screen shot, a recording session, or MIN MAX or Peak

record session, press the softkey labeled Save. To select the

name from the preset list, press +Name. To save to the same

name as before but with the next number, press the softkey

labeled Save. This second method makes it easy to save a

series of measurements simply by pressing the Save softkey

twice for each save operation.

When selecting the name for a save operation, position the menu

selector next to the desired name using the cursor buttons. Next

press the softkey labeled Save.

Viewing Memory Data

Viewing data stored in the Meter’s memory is performed through

the save menu. Press the softkey labeled Save. Position the

menu selector next to the menu item labeled View Memory and

press the softkey labeled View.

Note

To view data stored in memory, the Meter must not be

recording or performing a MIN MAX or peak record

session.

The Meter separates stored data into four different categories:

Measurement, MIN MAX, Peak, and Recording. Use the cursor

buttons to position the menu selector next to the desired saved

data category and then press the softkey labeled View. The

Meter displays the last record saved for the selected data

category.

If there are previously stored records, press the softkey labeled

Prev or 5 to page back through previously stored records. Press

the softkey labeled Next or 6 to page in the other direction. Press

Close to return to normal Meter operation.

Viewing Snapshot and Summary Data

After selecting the MIN MAX, Peak, or Measurement category

described in the Viewing Memory Data section above, pressing

View only displays the information stored at the time a Save was

performed. The display is reconstructed from this data when

viewed.

Viewing Trend Data

For the Recording category, the interval and event data stored

during a recording session are viewed on the Meter through a

trend-plot view, similar to a strip-chart recorder. See the

“Recording Measurement Data” section later in this manual for

an explanation of interval and event data.

After selecting the recording category described in the Viewing

Memory Data section above and pressing View, the recording

session’s summary screen is displayed (See Table 9). Press the

softkey labeled Trend to display the recorded data in a trend-plot

view. Table 7 shows the trend view along with a description of

each of its components.

To look at data stored in the individual records that make up the

trend, move the cursor to any point along the plot by pressing 6

or 5. The value and timestamp of the minimum, maximum, and

end-of-record values of the selected record are displayed at the

bottom of the cursor. All data contained in a record can only be

viewed on a PC running FlukeView Forms.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fluke 289 Seite 60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Fluke 289

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info