Bedienungsanleitung Garmin Edge 520 Plus (Seite 14 von 30) (Englisch)

691274

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

NOTE: When you enter emergency contacts, incident

detection is automatically enabled on your device.

Enable GPS on your Edge device (Changing the Satellite

Setting, page 16).

Viewing Your Emergency Contacts

Before you can view your emergency contacts on your device,

you must set up your rider information and emergency contacts

in the Garmin Connect Mobile app.

Select Menu > Contacts.

Your emergency contacts' names and phone numbers

appear.

Requesting Assistance

Before you can request assistance, you must enable GPS on

your Edge device.

Hold for four seconds to activate the assistance feature.

The device beeps, and sends the message after the five-

second countdown is complete.

TIP: You can select before the countdown is complete to

cancel the message.

If necessary, select to send the message immediately.

Turning Incident Detection On and Off

Select Menu > Settings > System > Incident Detection.

Cancelling an Automated Message

When an incident is detected by your device, you can cancel the

automated emergency message on your device or your paired

smartphone before it is sent to your emergency contacts.

Select Cancel > Yes before the end of the thirty-second

countdown.

Sending a Status Update After an Incident

Before you can send a status update to your emergency

contacts, your device must detect an incident and send an

automated emergency message to your emergency contacts.

You can send a status update to your emergency contacts

informing them you are not in need of assistance.

From the status page, select Incident Detected > I'm Okay.

A message is sent to all emergency contacts.

ANT+ Sensors

Your device can be used with wireless ANT+ sensors. For more

information about compatibility and purchasing optional sensors,

go to http://buy.garmin.com.

Putting On the Heart Rate Monitor

NOTE: If you do not have a heart rate monitor, you can skip this

task.

You should wear the heart rate monitor directly on your skin, just

below your sternum. It should be snug enough to stay in place

during your activity.

Snap the heart rate monitor module

onto the strap.

The Garmin logos on the module and the strap should be

right-side up.

Wet the electrodes

and the contact patches

on the back

of the strap to create a strong connection between your chest

and the transmitter.

Wrap the strap around your chest, and connect the strap

hook

to the loop

NOTE: The care tag should not fold over.

The Garmin logos should be right-side up.

Bring the device within 3 m (10 ft.) of the heart rate monitor.

After you put on the heart rate monitor, it is active and sending

data.

TIP: If the heart rate data is erratic or does not appear, see the

troubleshooting tips (Tips for Erratic Heart Rate Data,

page 11).

Recovery Time

You can use your Garmin device with wrist-based heart rate or a

compatible chest heart rate monitor to display how much time

remains before you are fully recovered and ready for the next

hard workout.

NOTE: The recovery time recommendation uses your VO2 max.

estimate and may seem inaccurate at first. The device requires

you to complete a few activities to learn about your

performance.

The recovery time appears immediately following an activity.

The time counts down until it is optimal for you to attempt

another hard workout.

Viewing Your Recovery Time

Before you can use the recovery time feature, you must put on

the heart rate monitor, and pair it with your device (Pairing Your

ANT+ Sensors, page 12). If your device was packaged with a

heart rate monitor, the device and sensor are already paired.

For the most accurate estimate, complete the user profile setup

(Setting Up Your User Profile, page 15), and set your

maximum heart rate (Setting Your Heart Rate Zones, page 11).

Select Menu > My Stats > Recovery Advisor > Enable.

Go for a ride.

After your ride, select Save Ride.

The recovery time appears. The maximum time is 4 days,

and the minimum time is 6 hours.

About VO2 Max. Estimates

VO2 max. is the maximum volume of oxygen (in milliliters) you

can consume per minute per kilogram of body weight at your

maximum performance. In simple terms, VO2 max. is an

indication of athletic performance and should increase as your

level of fitness improves. VO2 max. estimates are provided and

supported by Firstbeat. You can use your Garmin device paired

with a compatible heart rate monitor and power meter to display

your cycling VO2 max. estimate.

Getting Your VO2 Max. Estimate

Before you can view your VO2 max. estimate, you must put on

the heart rate monitor, install the power meter, and pair them

with your device (Pairing Your ANT+ Sensors, page 12). If your

device was packaged with a heart rate monitor, the device and

sensor are already paired. For the most accurate estimate,

complete the user profile setup (Setting Up Your User Profile,

10 ANT+ Sensors

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Edge 520 Plus Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Edge 520 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info