Bedienungsanleitung Jablotron JA-80V (Seite 2 von 10) (Englisch)

555056

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

The JA-80V LAN / PSTN line communicator - 2 - MKA51202

 the instruction texts are not case-sensitive and only ASCII characters

are allowed

 only one instruction can be in an instruction SMS

 a setting/unsetting instruction starting with the service code will only

be performed if setting/unsetting with the service code is enabled in

the control panel (to protect against unauthorized setting/unsetting

by installers)

 if there is any other text in the instruction not separated by “%”, the

instruction will not be performed

 if you are sending an instruction and you are not sure whether any

other text will be automatically added to the SMS (for example, when

using an SMS internet gate) type the instruction as: %code

instruction%%

 no other device receiving SMSes can be connected to the same

telephone line as the communicator.

3.3. Toll-free remote control by unanswered calls from pre-

authorized phones

If the telephone line provides CLIP protocol caller ID, then a limited

number of system functions can be activated remotely by calling the

system from pre-authorized phones and terminating calls before the

system answers. This way limited control of the system is free of call

charges. It is possible to pre-authorize phone numbers stored in

memories M1 to M8 (also used for event reporting – see 4).

To pre-authorize a telephone number store ∗ at the end of the

number and follow it by a single digit (1, 2, 3, 8 or 9) – see the notes in

section 4.

If this number calls, the communicator generates “∗ digit“ after the

first ring (as if it had been entered manually on the system keypad).

This toll-free remote control by unanswered calls enables the following

functions according to the digit stored at the end (after the ∗) of the tel.

number in memory:

∗1 setting the complete system (= ABC keypad button)

∗2 setting section A (= A button)*

∗3 setting sections A & B or B (= B button)*

∗8 PGX turns on for 2 sec. (if PGX is programmed for the pulse

function)

∗9 PGY turns on for 2 sec. (if PGY is programmed for the pulse

function)

Notes:

 if a phone sends no caller identification data it cannot be used for

this type of remote control by phone

 if phone calls end before the control panel answers, remote control is

for free

 a phone which is pre-authorized for toll-free remote control can also

temporarily authorize its keypad to fully operate the system (see

3.1) – just let it ring until the control panel answers the call

 if it is desired that the phone which is authorized for toll-free remote

control should not receive event reports, then turn the reports off

for that tel. number (see 5.3).

 setting (arming) with ∗1, ∗2 and ∗3 will work only if enabled in the

control panel

4. Reporting to phones

The communicator can report events occurring in the Oasis system by

sending SMS reports (if the telephone line supports CLIP protocol SMS

transfer) and/or by calling phone numbers with an acoustic signal (mostly

used as audible notification of an SMS to be read). Reporting can be

programmed for up to 8 phone numbers.

The most frequently desired reports are already assigned to the

telephone number memories by factory-default, so you only need to

program tel. numbers to the particular memories which have the desired

reports already assigned. If desired, other events can be reported to the

number too, i.e. the list of event reports assigned to the number can be

changed (see 5.3)

Factory-default reports assigned to the numbers M1 to M8

M Reports

Alarms and faults by SMS

larms and faults b

SMS +

hone call

(

ou answer the

larms b

SMS + a

hone call, with Settin

/Unsettin

Alarms by phone call (if you answer the call you hear a

siren sound)

8 Technical fault by SMS (suitable for an installer)

To program phone numbers to the M memories, enter the following

sequence while in Service mode:

81 M xxx...x ∗0

where: M is memory 1 to 8

xxx...x is a phone number (max. 20 digits)

Example: entering 81 5 777 777 777

∗

0 will store the number

777777777 in memory M5 (Alarms will be reported by SMSes + phone

calls, Setting/Unsetting and faults only by SMS)

To erase a number from memory M enter: 81 M ∗0

Notes:

 international phone numbers have to start the same way as if you call

them from the phone line which is connected to the communicator.

 SMS report text consists of: installation name, event name, number

and name of the event source (device or code), date and time. Example:

“Report from your alarm: setting 47: device Time 01.08. 11:27”

 if other events or texts should be reported to a particular number,

change the communicator settings (see 5.3 and 5.4)

 when storing tel. numbers, if you key in ∗7 after the last digit of the

phone number (the symbol ∗ is also stored) and continue with one

more digit (1, 2, 3, 8 or 9), then if this tel. number calls the system,

the system will behave as if ”∗ digit“ had been keyed in just after the

first ring, i.e. as if it had been entered manually on the system

keypad – see section 3.3. Example: entering 81 5 777 777 777

∗

0 authorizes calls from tel. number 777777777 to trigger output

PGY for 2 seconds (after the first ringing signal from this number the

∗9 command will be executed. The PGY output should be

programmed for a 2 sec. pulse function. This setting is suitable for

opening an electric door lock, automatic gate etc.

4.1. Programming

The most convenient programming is best done by a PC running

Comlink software or via the Internet and website: www.GSMLink.cz

by programming SMS – PRG sequence

Programming is also possible via the system keypad:

 The control panel must be in Service mode - if it is not, enter ∗0

Service code (factory default: 8080) while the system is unset.

 Enter the relevant programming sequences – see the following

description

 To exit service mode press the # key

5. Programming sequences

Function Sequence Options Factory default

Language setting 981 xx

xx=01 to 17 where:

01=EN,02=CZ,03=SK,04=NL,05=DE,06=PL,0

7=DA,08=IT,09=PT,10=FI,11=NO,12=SV

13=FR, 14=HU, 15=RU, 16=TR, 17=SP

English

Tel. number programming for

reporting to telephones

81 M xx..x ∗0

M = memory 1 to 8

xx..x = tel. number (max.20 digits)

keying in ∗7 = ∗

81 M ∗0 erases the number in memory M

all M1 to M8 erased

Selection of events to report by

SMS

82 M ec x

M = tel. number memory from 1 to 8

ec = event code (see 5.3)

M1 & 2 alarms by SMS

M3 & 4 alarms by SMS and call

Jablotron JA-80V Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info