Bedienungsanleitung Jablotron JA-80V (Seite 3 von 10) (Englisch)

555056

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

The JA-80V LAN / PSTN line communicator - 3 - MKA51202

Function Sequence Options Factory default

Selection of events to report by

phone call

83 M ec x

x=1 report, x=0 no report

M5 & 6 alarms by SMS and call + Set/Unset

by SMS

M7 alarms by call

M8 technical faults by SMS (to installer)

SMS/phone call communication

checking period

84 hhmm

hhmm = hours and minutes in range from

00:00 to 24:00

(The time to wait after the last SMS/phone call

report before performing an SMS/phone

communication check)

24:00

SMS text editing*

Texts can be edited by Comlink software or by SMS instruction:

code TXT n,text,n,text... or by www.GSMLink.cz

via Internet

see 5.4

Enable reporting to phones 80 x

x=0 disabled

x=1 enabled (all programmed by 82.. & 83..)

x=2 enabled without reporting

setting/unsetting by users 41 to 50 (codes,

cards & key-fobs) and master code

setting/unsetting

x=3 only if ARC1 is not responding

x=4 only if ARC1 is not responding

x=1

enabled

Phone number for instant remote

access

902 xx..x ∗0

xx..x = tel. number (max.20 digits) erased

Remote access 903 x

x=0 disabled

x=1 enabled (by phone and Internet)

enabled

Forwarding of incoming SMSes 926 x

x=0 no, x=1 yes = if the incoming text is not an

SMS instruction it will be forwarded to the first

programmed number in memories M1 to M8

yes

Reaction to incoming calls 904 x

x=0: no reaction

x=1 to 8: answers after 1 to 8 rings

x=9: answers after the 2

call

answers after 5 rings (25s)

Initialisation of GSMLink

communication

913 initialises communication to GSMLink

Tel. number to initialise GSMLink

communication

914 xx..x ∗0

xx..x = tel. number (max.20 digits) erased

Tx SMS center tel. number

942 xx..x ∗0

xx..x = tel. number (max.20 digits)

erased

Rx SMS center tel. number

943 xx..x ∗0

xx..x = tel. number (max.20 digits)

erased

Testing reporting to an ARC 961 a

a=1=ARC1, a=2=ARC2

Test calls to a phone number 962 M M = tel. number memory from 1 to 8

Programming by SMS

System can be programmed remotely via SMS instruction code PRG seq, seq,... where seq is programming

sequence set also from the keypad (e.g. 8080 PRG ∗08080,201,# set the 10s exit delay)

Triggering LAN re-log-in 935 The communicator will log out of the LAN network and then re-log-in (DHCP update)

Communicator reset 98080 Resets to the factory default settings and erases all phone numbers

Automatic DHCP 930 x

x=0 disabled

x=1 enabled

enabled

Communicator IP address 931 xx..x

xx..x = IP address 12 digits (if automatic

DHCP disabled)

192.168.001.211

Network mask 932 xx..x

xx..x = network mask 12 digits (if automatic

DHCP disabled)

255.255.255.0

Network gateway address 933 xx..x

xx..x = IP address 12 digits (if automatic

DHCP disabled)

192.168.001.001

DNS IP address 934 xx..x

xx..x = IP address 12 digits (if automatic

DHCP disabled)

192.168.001.001

ARC main tel. number/IP address

01 a xx..x ∗0

ARC backup tel. number/IP

address

02 a xx..x ∗0

a=1=ARC1, a=2=ARC2, xx..x = IP address &

port for ARC1 – e.g. 01 2 ∗8 192 168 001 123

08080 ∗0 (∗8= signifies an IP address, it must

have 12 digits followed by a 5 digit port

number).

Tel. number for ARC2 (max.20 digits)

Entering 01p∗0 or 02p∗0 will erase the

number/address

erased

Installation (alarm system) ID for

ARC use

03 a zz..z ∗0

a=1=ARC1, a=2=ARC2, zz..z = ID number

max. 8 digits 0 to 9 and ∗1=A to ∗6=F

(hexadecimal number)

0000

Selecting the ARC protocol 04 a x

a=1 ARC1, a=2 ARC2

x=0 CID, x=1 IP CID

CID

Selection of events to report to

ARCs

05 a ec x

a=1 ARC1, a=2 ARC2

ec event code (see 5.26)

x=1 report, x=0 no report

all events are reported

Defining the delay before data is

resent to an ARC

06 a x

a=1 ARC1, a=2 ARC2

x=0 to 9 min. (0=immediately, without delay)

1 minute

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-80V Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info