Bedienungsanleitung Jablotron JA-80V (Seite 4 von 10) (Englisch)

555056

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

The JA-80V LAN / PSTN line communicator - 4 - MKA51202

Function Sequence Options Factory default

ARC communication checking

period

07 a hhmm

a=1 ARC1, a=2 ARC2

hhmm = hours and minutes after last report

(The time to wait after the last report before

performing an ARC communication check)

2400 (24 hours after last report)

Enable ARC reporting (ARC2

backs up ARC1)

00 a x

a=1 ARC1, a=2 ARC2

x=0 reports disabled, x=1 reports enabled, x=2

(only for ARC2) = ARC2 backs up ARC1

ARC reporting disabled

Recording reports sent to ARCs in

the control panel memory

08 x

x=0 no (only records ARC communication

faults, if communication checks are enabled)

x=1 yes (all reports except communication

checks)

yes

Indicate an ARC communication

fault if a report is not successfully

received by an ARC within 110

sec of transmission.

09 x

x=0 no

x=1 yes

IP address for data transmission

013 xx..x ∗0

IP address and port in format – e.g..: 013

∗8 077 104 220 129 07070 ∗0

∗8 mark IP address which must contain 12 digits

followed by 5 digits for the port.

Entering 013∗0 IP erase the setting

77.104.220.129 7070

(img.jablotron.com)

Locking the ARC settings

901 xx..x ∗0

xx..x = an installer-defined locking code (4 to 8

digits). Entering this code and then exiting

service mode will lock the ARC settings

901∗0 will erase the code (= permanently

unlocked)

unlocked

Unlocking the ARC settings

900 xx..x ∗0

xx..x = a locking code used by sequence 901

ARC programming can be temporarily

enabled in service mode by entering this

sequence. It will then relock on exiting service

mode

These parameters effect reporting to the ARC and it is impossible to change them if the ARC settings are locked.

* These parameters cannot be programmed from the system keypad, but they can be programmed by sending SMS instructions or by Comlink software.

5.1. Language setting

Language of the text used by the communicator can be set by

instruction:

981 xx

Where:

xx is number of the language – see the following list:

01 EN English 10 FI Finnish

02 CZ Czech 11 NO Norwegian

03 SK Slovak 12 SV Swedish

04 NL Dutch 13 FR French

05 DE German 14 HU Hungarian

06 PL Polish 15 RU Russian

07 DA Danish 16 TR Turkish

08 IT Italian 17 SP Spanish

09 PT Portuguese

Note:

 Set the language before editing the text in the system (change of

the language will change the text to the factory default)

 Change of the language in the communicator will automatically

result in changing the language in the connected keypad (also the

wireless keypad if connected)

 Set language will not be change when reset is performed

Example: by setting 98102 the Czech language will be set.

Factory default : 98101 = English

5.2. Programming tel. numbers for reporting to phones

See part 4.

5.3. Selection of the events reported to phones

The factory-default list of reported events and their assignment to

telephone numbers M1 to M8 can be altered by this sequence.

 The complete list of reportable events is shown in the following

table.

 It is possible to select whether the event should be reported by an

SMS or by a phone call, or by both an SMS followed by a phone call

 Each event has pre-programmed factory-default SMS text. These

texts can be edited (see 5.4). The acoustic signals for phone call

reporting are fixed and cannot be changed (e.g. an alarm is

indicated by a siren sound if a reporting call is answered)

List of events which can be reported to phones and their factory-default assignment to particular phone numbers

Phone number memory M

ec Event

1 2 3 4 5 6 7 8

01 Intruder alarm - instant S S SC SC SC SC C

02 Intruder alarm - delayed S S SC SC SC SC C

03 Fire alarm S S SC SC SC SC C

04 Panic alarm S S SC SC SC SC C

05 Number of permitted incorrect code-entries

exceeded

S S SC SC SC SC C

06 Alarm triggered during control panel

power-up

S S SC SC SC SC C

07 Tamper alarm S S S S S S

08 End of tamper alarm

09 End of alarm indication

10 Alarm cancelled by user S S S S S S

11 Setting S S

12 Unsetting S S

13 Partial setting S S

14 Codeless setting S S

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-80V Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info